On models with a shipping rod, it is located on the right side panel, toward the bottom of the washer, between the front and rear legs.
What happens if you don t remove shipping bolts from washing machine?
You need to remove the shipping bolts. If the four shipping bolts of your machine are still attached to the back of the washer, they will cause a loud noise and vibration during the operation of the machine; which can lead to a permanent damage of the washer.
Do you need shipping bolts for washer?
Are all washing machine shipping bolts the same?
Some brands of washing machines may have shipping bolts that are all the same length, and any shipping bolt can be used in any hole.
Where are the shipping bolts on a GE washer? – Related Questions
How do you match washers to bolts?
A.
It is important to note that when matching a washer with a screw or a bolt, the diameter of the shaft of the screw or bolt should be matched to the inner diameter of the washer. For example, a ¾-16 bolt should be matched with a ¾ washer.
Why do shipping bolts make washer shake?
If the drum does not wobble, the shipping bolts are likely still holding it in place, which can cause the whole washer to shake instead of just the drum inside.
What size are shipping bolts on a washing machine?
They are typically 4 to 12 in (100 to 300 mm) in length, although any size is possible as it depends on the type of device being transported. The most common example of transit bolts is the securing of the drum of a washing machine while it is transported from shop to property (or property to property).
Do all washing machines have the same fittings?
All washing machines should use standard sizes and fittings. But there are variances in design across different manufacturers and a few potential problems as discussed in this article. You will always get new fill hoses with a new washing machine.
Do all washers have the same plug?
Washer –Washing machines are large appliances that do not require customized electrical hookups, they simply need a 120 volt outlet that can take 3 prongs.
What are the different types of washers for bolts?
There are three main types of washers: plain washers, spring washers and lock washers.
How do I know what size bolt washer I need?
Washers are not. It is important to note that when matching a washer with a screw or a bolt, the diameter of the shaft of the screw or bolt should be matched to the inner diameter of the washer. For example, a ¾-16 bolt should be matched with a ¾ washer.
Should washer be bigger than bolt?
– Washers must always be larger than exact diameter of screw. Determining the Diameter: Both nuts and washers are sized by the fasteners they fit.
Which washer goes first on a bolt?
Place the lock washer under the threaded fastener.
To help it accomplish this, put the lock washer on first, below the fastener. If your project calls for other washers or hardware elements, they should go on before the lock washer so that it can hold them in place.
Is it OK to stack washers on a bolt?
It is not a good practice to stack washers in a fastener joint. Each stacked element acts like springs in series, consequently, fastener joint stiffness would be compromised.
Does a washer go on the same side as a bolt?
However, spring washers are placed on the nut side of the fastener only, unlike flat washers, which are placed on the bolt and nut sides. Spring washers act like a spring and provide a preload between two surfaces.
Do you need a washer on both sides of a bolt?
Generally, it is essentiall on the side where you fastenning the connection (whether it’s a bolt or nut). Often used on both sides, if you (for any reasons) cannot prevent the other side from turning while fastenning. It’s to prevent surface damage (especially to any possible surface treatment).
Does it matter which way a washer goes on a screw?
There is no fixed rule about which side goes up and which goes down, but given the issue of bearing surface pressure mentioned above, it’s more effective to put the burred side facing down.
Which side is the beveled side of a washer?
The bevel side of the washer is facing towards the bolt head.