How to run diagnostics and read error codes on a Maytag washer?

How do I reset my Maytag top load washer?

Follow the below steps:
  1. Remove the washer’s plug for one minute.
  2. Reconnect the power, then lift and close the lid six times in a 12-second interval.
  3. Keep in mind that for the procedure to function, the lid must close properly six times in a row.
  4. Run a test load afterward to confirm that the washer has reset.

How do you put a washing machine in self test diagnostic mode?

How do I get my Maytag washer out of diagnostic mode?

Turn the washer control dial at least 3 full rotations to the left like you were clearing a combination lock. Then rotate the knob 3 clicks to the right, one to the left, and one more to the right, with about a half second to one second between clicks.

How to run diagnostics and read error codes on a Maytag washer? – Related Questions

How do I boot into diagnostic mode?

Press WINDOWS-R on the keyboard to bring up the Run window, enter MSCONFIG and click OK. Under the General tab, click “Diagnostic startup.”

How do I reset my Maytag control panel?

How to reset a dishwasher control panel
  1. First press the “Cancel/Resume” button, which won’t be illuminated, then unplug the appliance from the outlet.
  2. Wait approximately 1 minute, plug the cord back into the AC outlet or flip the breaker back on.
  3. Start a new cycle and check if the dishwasher is working properly.

How do I turn off diagnostic mode?

How do you force a washing machine to reset?

If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

How do I reset the control panel on my washing machine?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

How do you clear a washing machine code?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

What are the codes for a Maytag washer?

Error Codes in your Maytag Top Load Washer:
Error code Error
LdL Lid is not locking.
LdU Lid cannot unlock.
LF, Lo FL or F8 E1 The washer is taking too long to fill.
lid The washer lid was left open.

Can you reset a washing machine by unplugging it?

Reset your washing machine

What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.

What is diagnostic mode on washing machine?

The washer’s diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.

What does diagnostic mode do?

Diagnostic mode is an environment that runs a set of tests before the browser starts. These tests vary in sophistication, from trivial checks that critical files exist, to more complex (and time consuming) tests that test the integrity of the key databases.

What are the four trouble symptoms of washing machine?

10 Most Common Washing Machine Problems
  • It Bounces Around.
  • It’s Noisy.
  • Clothes Are Getting Ripped.
  • Improper Or Slow Draining.
  • My Washing Machine Won’t Spin.
  • There’s No Water.
  • The Door Won’t Open.
  • It’s Smelly.

What is the first step of troubleshooting the malfunctioning washing machine?

The first thing you should always check is if the machine is plugged in. It may sound silly but dozens of times this problem has been solved by simply checking the plug. If the power cord is plugged in, check to be sure the outlet has power and that your circuit breaker wasn’t tripped. Check the water supply.

What is the first thing you should do when troubleshooting any malfunction?

Step 1. Gather information. The first troubleshooting step for just about any problem is gathering information about it. This can be information about why something unexpected is happening or a missing capability.

Is it worth repairing a 5 year old washing machine?

Replace: An older machine that breaks down frequently and has needed several repairs in the past few years could keep hurting your wallet. Consider making the switch to a new appliance if your old one is more than 50% through its life expectancy and the cost of a repair would be more than half the cost to replace.

Leave a Comment