Why is my washing machine stuck on spin cycle?

If resetting the washer did not work, then it most likely means that your timer is malfunctioning. The washer could have gotten stuck on any cycle, unfortunately, it just got stuck on spin. Now you can disassemble the control panel of the washer to test the timer with a multimeter and replace it if necessary.

How do you reset the spin cycle on a GE washer?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

Do GE washers have a reset button?

If your washer isn’t working, disconnect it from the power source for one minute. Afterward, plug it back in and quickly lift and lower the lid six times within 12 seconds. And this should reset the motor so you can properly start a cycle.

How long is the final spin cycle on a GE washer?

A spin cycle takes around 3 minutes on average, but can take from 2 to 12 minutes depending on which cycle and size of the load. If, however, for some reason your laundry is still dripping wet after the cycle has finished, there is also an option to put on another separate spin cycle.

Why is my washing machine stuck on spin cycle? – Related Questions

How do I reset my GE washing machine?

How to Reset GE Washer Models
  1. Shut off the circuit breaks or the fuse to the washer.
  2. Unplug your washer and wait at least two minutes before plugging it back in.
  3. If your model has a manual control panel, turn the knob to any setting other than the final spin.
  4. Plug the unit back in and restore power to your laundry room.

Why is the spin cycle taking so long?

Cycles get lengthened at the end of the wash as well. All washers spin as fast as they can at the end of the cycle. This is done to extract excess water from your wet clothes. So if the load sense is activated again and your laundry is still sopping wet, the spin cycle gets extended.

How long does the final cycle take on a washing machine?

A normal wash cycle usually takes between 50 minutes to an hour to complete. However, this time could be faster or slower depending on load size and the cycles or options you choose.

Why does my GE washer take so long?

A washer that continuously takes too long to wash may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.

How long is the venting cycle on GE washer?

The Ultrafresh Vent is great! It really gets the inside of the washer dry (this was why we chose this washer). Keep in mind, though, that this feature cycles on/off for about 8 hours.

How long does the drain and spin cycle take?

Now we know what “rinse and spin” is, when do we use it? In most instances, you will need to give your laundry the full treatment, but sometimes all you need is a quick rinse (the cycle generally lasts about 45 minutes depending upon load size)!

Will a washer spin if it doesn’t drain?

It’s possible that your washing machine is spinning, but not draining. It’s also possible that it’s draining, but not spinning. In some cases, it might not be doing either step—but it’s often easy to get to the bottom of the problem.

Does water drain on spin cycle?

What Does the Drain Function on a Washing Machine Do? A washing machine’s drain function removes water from the tub during the spin cycle. The washer pump forces water from the bottom of the appliance into the drain hose.

Does Spin Cycle get rid of water?

The spin cycle works to extract moisture from your clothes at the end of the wash cycle. The higher the ‘RPM’ the drier the clothes are, reducing additional drying time in either the tumble dryer or by hanging outside.

How do I know if my washing machine drain hose is clogged?

Water Doesn’t Appear or Drain Normally

If the machine turns on and you hear the sound of the water pump, but no actual water appears, then you most likely have a clogged drain hose. The hose can be removed from the back of the machine and be checked for any dirt or dust that may have created a blockage.

How do you fix a washer that won’t drain?

What to Do When Your Washing Machine Won’t Drain
  1. Perform a Master Reset. Unplug your washer for about one minute.
  2. Test the Lid Switch Assembly.
  3. See if the Drain Hose is Kinked.
  4. Check the Drain Hose or Pump for Clogs.
  5. Clean out the Coin Trap.
  6. Check the Water Level Control.
  7. Schedule Washing Machine Repair.

How to reset washing machine?

How do you reset a GE washer that won’t drain?

Unplug the washer or shut off the washer circuit breaker or fuse. Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting. Restore the power.

Leave a Comment