A broken drive belt is one of the most common part failures that results in an LG front load washer not spinning. The drive belt is suspended around the wash tub via two pulleys, using power from the washer’s motor to spin the wash tub. Over time, this rubber belt can tear and break, leaving the tub unable to spin.
How do I force my LG washer to spin?
For LG front load washers, turn the unit on and without touching the selector dial move to the spin speed selection button. Next, press the button until you see your desired spin speed highlighted. Then press the Start button. The unit will drain any excess water before it spins.
How do I reset my direct drive LG washer?
How to reset the washing machine:
Press POWER to turn the washer off.
Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
With the power disabled, press and hold the START/PAUSE button for 5 seconds.
Plug the washer back in, or turn the circuit breaker back on.
Why is my washing machine not spinning around?
Here are a few common reasons a washer won’t spin: The washing machine is too full. The load is improperly balanced. The washer itself isn’t balanced correctly.
Why is my LG direct drive washer not spinning? – Related Questions
Why is my washer not spinning but it will drain?
The washing machine drains but won’t spin. A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure.
What is the most likely cause if a washing machine will not agitate or spin?
Here are some of the main reasons your washing machine agitator not spinning: An obstacle jammed in the agitator. A broken lid switch. A loose or broken drive belt.
How do you reset the agitator on a washing machine?
How do you reset a washer that won’t spin?
What is the most common fault on a washing machine?
A washing machine not draining is one of the most common problems we encounter. It can be caused by one of the following: – The drain hose or pump is clogged with a small item of clothing, residual gunk or other debris. – The washer is malfunctioning and not engaging the drain/spin cycle properly.
How do I know if my washing machine agitator is broken?
Why did my washing machine stopped agitating?
Your washer may not be agitating due to worn-out directional cogs. Check to see if your machine’s agitator has two parts, allowing it to move the water left or right. If it does, and the cogs are damaged, the upper part of the agitator won’t properly connect to the bottom part.
Why is my top loader not spinning?
An imbalanced drum is a common reason for your machine not spinning. The easiest way to avoid an imbalanced drum is by making sure you don’t overload your washing machine, or if you have one large piece of laundry, add smaller pieces to balance out the load. You may also need to check that your machine is level.
How do you fix a washing machine that does not agitate?
What are the four trouble symptoms of washing machine?
10 Most Common Washing Machine Problems
It Bounces Around.
It’s Noisy.
Clothes Are Getting Ripped.
Improper Or Slow Draining.
My Washing Machine Won’t Spin.
There’s No Water.
The Door Won’t Open.
It’s Smelly.
What are common problems with LG washing machines?
However, like all washers, LG washers are still prone to wear and tear. The most common issues with LG washers relate to the washer not draining, wires breaking, or excess water caused by a defective water inlet valve.
Washer Not Draining.
Broken Motor Wire Harness or Position Sensor Wire.
Washer Overfilling or Leaking.
Is it worth repairing a 5 year old washing machine?
Replace: An older machine that breaks down frequently and has needed several repairs in the past few years could keep hurting your wallet. Consider making the switch to a new appliance if your old one is more than 50% through its life expectancy and the cost of a repair would be more than half the cost to replace.
How do you run a diagnostic on a washing machine?
How do I put my LG washer in diagnostic mode?
Press the POWER to turn on the washer. Place the mouthpiece of your phone between the Smart Diagnosis logo and the POWER button. After pressing the Start Diagnosis button, press and hold the TEMP button until a countdown displays on the washer.