Why is my Kenmore Elite washing machine not spinning?
•
If the clutch is worn out, it may prevent the tub from spinning. If the clutch band kit is worn out, replace it. The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning.
How do you reset a Kenmore washer that won’t spin?
Why does my Kenmore washer agitate but not spin?
Inspect the motor coupling to determine if it is broken. If the motor coupling is broken, replace it. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it.
What would cause a Kenmore front load washer not to spin?
Why is my Kenmore Elite washing machine not spinning? – Related Questions
Why does my washer turn on but not spin?
Here are a few common reasons a washer won’t spin: The washing machine is too full. The load is improperly balanced. The washer itself isn’t balanced correctly.
Why is my washer not spinning but it will drain?
The washing machine drains but won’t spin. A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure.
How do you reset a washer that won’t spin?
How do you run a diagnostic on a Kenmore front load washer?
3 Answers
With the washer empty, close the door.
Push “control/on” or “Start”
Select “Drain/Spin”
Select “No Spin” by pressing SPIN SPEED touchpad.
Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
C:00 should light up and begin the diagnostic.
How do I reset my Kenmore front load washer?
How do I reset my Kenmore Elite?
There’s an easy fix for it, which is to reset your refrigerator. More often than not, it will resolve your problem. To do this, unplug its cord from the outlet.Then replug it after a minute.
How do you reset the sensor on a Kenmore washing machine?
2 Answers. @mountian first thing you want to do is to unplug your machine then plug it back in after a short while (I’d give it 10-15min) This will act like a reset. After that make sure that your power outlet works. If it dos not check your circuit breakers or fuses.
How do you force a washing machine to reset?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How do I reset my top load washer?
Motor Reset Procedure:
Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.
How do you put a washing machine in diagnostic mode?
What are the four trouble symptoms of washing machine?
10 Most Common Washing Machine Problems
It Bounces Around.
It’s Noisy.
Clothes Are Getting Ripped.
Improper Or Slow Draining.
My Washing Machine Won’t Spin.
There’s No Water.
The Door Won’t Open.
It’s Smelly.
What is the first step of troubleshooting the malfunctioning washing machine?
A first step when troubleshooting any appliance is to confirm that it’s drawing power. If your washing machine isn’t showing any signs of life, check that the machine is plugged in. You can also test the outlet with another appliance, such as a phone charger.
How do I boot into diagnostic mode?
Press WINDOWS-R on the keyboard to bring up the Run window, enter MSCONFIG and click OK.Under the General tab, click “Diagnostic startup.”