The most common reason GE washers stop spinning is a faulty lid switch. The purpose of the switch is to monitor if your washer door is closed, so the main control board knows to let the washer cycle start. This is how to inspect the lid switch: Switch the washer off or unplug it.
How do you reset a GE washer that won’t spin?
How do I force my GE washer to spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
Why won t my GE washer drain and spin?
There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If the washer drains properly, then the clog has likely cleared. If water remains in the washer, check for a pinched or flattened drain hose.
Why is my GE top load washer not spinning? – Related Questions
Why is my washer not spinning but it will drain?
The washing machine drains but won’t spin. A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure.
Why is my washer running but not spinning?
Here are a few common reasons a washer won’t spin: The washing machine is too full. The load is improperly balanced. The washer itself isn’t balanced correctly.
Why is the drain and spin cycle not working?
Top reasons washers won’t spin or drain
Worn drive coupler or broken belt – A top-load washer drive coupler connects the motor to the washer transmission. The coupler can wear out over time or fail, especially if the tub is consistently overloaded. Similarly, a drive belt can wear out, break, or slip on the pulleys.
How do you fix a GE washer that won’t drain?
A kink or clog in your washing machine’s drain hose could be interfering with water flow and preventing your machine from draining properly. To inspect the drain hose, turn off the power to the washer, disconnect the hose (have a bucket ready to catch any water), and check the hose for damage or obstructions.
How do you manually drain a GE washing machine?
Here’s how to do it.
TURN OFF THE POWER. Unplug the washing machine from the power outlet.
REMOVE LAUNDRY. Take out any clothing that’s in the washer tub.
EMPTY THE TUB. Use a bucket to scoop the water out of the washer tub.
MOVE WASHER AWAY FROM THE WALL.
DISCONNECT DRAIN HOSE.
PINPOINT THE ISSUE.
How do I reset my GE top load washer?
How to Reset GE Washer Models
Shut off the circuit breaks or the fuse to the washer.
Unplug your washer and wait at least two minutes before plugging it back in.
If your model has a manual control panel, turn the knob to any setting other than the final spin.
Plug the unit back in and restore power to your laundry room.
How do I put my GE top load washer in diagnostic mode?
Is there a reset button on a GE washing machine?
How to reset GE washers with a timer control knob. Unplug the washer or shut off the washer circuit breaker or fuse. Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting. Restore the power.
How do you hard reset a washing machine?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do you reset a washing machine without unplugging it?
Washers Without a Reset Button
For washers with a knob control, turn the dial clockwise to any cycle other than “Final Spin.” With button controls, select any cycle other than “Spin.” Check that the water to the washing machine is on. Turn the breaker back on. Turn the washing machine on.
How do you reset a washing machine sensor?
How do you put a washing machine in diagnostic mode?
How do I reset my washing machine motherboard?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do you restart a sensor?
To reset a sensor, turn the device over and look for the circle on the back labeled “RESET” (See photo below).Insert a paperclip or other thin wire through the label to make a hole, and depress the reset button. You’ll feel it ‘click’ when it is depressed. The sensor will reset and rejoin the network.
What causes sensor failure?
Dust, other contaminants, vibrations, shocks and exposure to high temperatures all have a shortening effect on the average lifespan of a sensor, so it is important to look for a solution that overcomes these problems by design, rather than just accepting frequent sensor failure and replacement as part and parcel of