The most common reason GE washers stop spinning is a faulty lid switch. The purpose of the switch is to monitor if your washer door is closed, so the main control board knows to let the washer cycle start. This is how to inspect the lid switch: Switch the washer off or unplug it.
How do you reset a GE washer that won’t spin?
How do you fix a top-loading washer that won’t spin?
What to Do When Your Top-Loading Washer Won’t Spin
The Mid-Spin Check.
Check the Lid Switch.
Look for Jammed Clothing.
Balance Laundry Loads.
Track the Cycle Progress.
Investigate the Washer Belt (if it has one)
How do I force my GE washer to spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
Why is my GE top load washer not spinning? – Related Questions
Why won’t my GE washer spin and drain?
There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If the washer drains properly, then the clog has likely cleared. If water remains in the washer, check for a pinched or flattened drain hose.
Why won’t my GE washer agitate or spin?
If the washer is not agitating, you may need to reset your washer motor. If your washer senses a power spike, an unbalanced load or disruption in power, it will send a fault code to the motor and may require the motor to be reset.
How do I make my washing machine spin only?
How do I reset the spin cycle on my GE washing machine?
How do you do a hard reset on a GE washer?
How to Reset GE Washer Models
Shut off the circuit breaks or the fuse to the washer.
Unplug your washer and wait at least two minutes before plugging it back in.
If your model has a manual control panel, turn the knob to any setting other than the final spin.
Plug the unit back in and restore power to your laundry room.
Is there a reset button on a GE washing machine?
How to reset GE washers with a timer control knob. Unplug the washer or shut off the washer circuit breaker or fuse. Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting. Restore the power.
How do you reset a GE top load washer motor?
Motor Reset Procedure:
Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.
How do I put my GE top load washer in diagnostic mode?
How do I reset the control panel on my GE top load washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do you force a washing machine to reset?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do I bypass the lid lock sensor on a GE washer?
Why is the spin light flashing on my GE washer?
Spin LED light is flashing: If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle and will stay illuminated for a short time after cycle completion.
How do I reset my spin?
What causes spin cycle to stop working?
An unbalanced load of laundry is one of the most common causes of an inadequate spin cycle. Sometimes clothing can settle on one side of the drum, throwing off the motion of the washing machine. (This happens most often when washing large and heavy items like comforters and heavy coats.
What do you do if your spin cycle isn’t working?
A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure. To troubleshoot this, hold the switch down with your finger (with the lid open) and start a spin cycle.