Where is the drain plug on my Samsung washer?

How do I drain the water from my Samsung washer?

To drain your washer in an emergency, follow these steps:
  1. 1 Unplug the washing machine from the power supply.
  2. 2 Open the filter-cover.
  3. 3 Unscrew the emergency drain cap by turning it to the left.
  4. 4 Grip the cap on the end of the emergency drain tube, and then slowly pull it out about 15 cm (about 6 inches).

Is there a drain plug on the bottom of a washing machine?

You will see a small cutout along the bottom of the washer. Grasp the cutout and pull it toward you to pop it off. Depending on your washer, Remove and Replace says you may need to use a small flat-head screwdriver to help pry off the cover. You will have access to the drain trap cap or plug.

Where is the drain plug on washer?

The drain pump may be located behind removable panels in either the front or back of the washing machine, even underneath the appliance, requiring you to tip the machine forward to access it (consult your owner’s manual for instructions). You’ll see a drain hose and inlet hose connected to it with spring clamps.

Where is the drain plug on my Samsung washer? – Related Questions

Do all washers have a drain plug?

Every washing machine has a drain plug with a filter that needs to be removed and cleaned periodically. You should consult your owner’s manual to find out where your machine’s drain plug is located and how to safely remove it.

How do I unclog my washer drain?

Tip 2: pour boiling water and baking soda down the drain
  1. Remove the hose from the drain.
  2. Fill a bucket with boiling water and a package of baking soda.
  3. Slowly pour the mixture down the drain with a funnel.
  4. Wait about 10 minutes.
  5. Pour water down the drain again to check whether water runs through properly.

How do you drain a top load washer?

If your top-loading washer did not drain by unblocking the drain hose or initiating drain prompts, siphon the water into buckets with a hose.
  1. Open the Lid. Open the washing machine lid.
  2. Unplug the Washer and Turn Off the Water.
  3. Remove the Clothing.
  4. Place Buckets.
  5. Set Up a Water Siphon.
  6. Drain the Washing Machine Drum.

How do I know if my washing machine drain hose is clogged?

Water Doesn’t Appear or Drain Normally

If the machine turns on and you hear the sound of the water pump, but no actual water appears, then you most likely have a clogged drain hose. The hose can be removed from the back of the machine and be checked for any dirt or dust that may have created a blockage.

Where is the drain pump on a top load washer?

The drain pump is located underneath the washer and handles draining the tub between cycles. This guide will walk you step-by-step through replacing the drain pump for a top-load washer.

How do you manually drain water from a washing machine?

If you have a drain pump filter only, place the shallow container up against the machine, directly under the filter, to catch the water. Turn the knob slowly until water starts coming out. Fill the container, turn the knob off, dump the water into a sink or basin, and repeat until the water has been drained completely.

Why won’t my washer drain and spin?

Washer Won’t Drain

Malfunctioning drain pump – A small object or article of clothing may have created an obstruction in the drain pump, or a damaged impeller could cause the pump to fail mechanically. If the pump doesn’t appear to be damaged and is free of obstructions, it’s possible the pump has failed electrically.

What causes a Samsung washer not to drain?

When your Samsung washer doesn’t drain, it can be alarming to find your clothes sitting in water in the wash tub. What causes draining problems? It could be because the washer isn’t level or the drain tube is clogged or pinched. Adjust the legs of your washer, as needed, and check the drain tube for kinks or damage.

Why won t my Samsung washer drain and spin?

If your washer doesn’t drain or spin:

Make sure the drain hose is straightened. If you have a kink in the hose, it may restrict any water from draining. Make sure the debris filter is not clogged. If you are able to open and close the door, close it and press START/PAUSE.

Why is my washer full of water and won’t drain?

The most probable cause is a clogged pump filter. The pump filter should be cleaned every three months or when it’s clogged. This filter is installed to catch foreign objects like buttons or coins, and to prevent these items from entering the drain hose.

What happens if washing machine drain is clogged?

A clogged drain causes water to back up into the standpipe and spill on the floor. Clearing the clogged drain will usually resolve the problem. The washing machine drain hose goes down about two feet into the plumbing drain standpipe.

Why is my washer drain backing up?

Washing machines overflow for a variety of reasons—the leading culprit, though, is a clog in the drain pipe. Lint and other debris come off of clothing during the wash cycle and are drained from the unit alongside the dirty water, potentially leading to clogs that can wreak havoc on your drain pipe.

How do you fix a drain that keeps backing up?

Quick Fixes for Sewer Backups
  1. Use a Plunger – the easiest and most available drain opener around.
  2. Buy a Liquid Drain Cleaner – to unclog a sink or bathtub.
  3. Release Pressure – by turning off the water at the main supply first.
  4. Chemical Drain Cleaning – help with tree roots blockages.

Leave a Comment