Pressed steel bulldog hinges are a swing gate hinge that permits the gate to swing 90º from the closed to the open position. Bulldog hinges are attached to the post with a 1/2″ U-bolt.
How do you put hinges on a chain link gate?
How do you install a double gate chain link fence?
Chain Link Double Swing Gate Installation Instructions
Check to Ensure that the Gate Posts are Level.
Tie a String Between the Fenceposts.
Attach the Gate Latch Hardware to the Gates.
Attach the Hinges to the Gates.
Attach the Gates to the Posts.
Line Up the Gates and Drill for the Centre Drop Pin.
How do you dog proof the bottom of a chain link fence?
Install tension wire on the bottom of the fence line. This wire reinforces the bottom of a chain link fence and helps prevent the bottom from ‘pulling’ up if an animal tries to push the fabric out and away from the fence line.
What is a bulldog hinge? – Related Questions
How much should be the gap between chain link and gate post?
This is easily done by stretching a string along the property line and setting the posts 4″ inside. Distance between gate posts is determined by adding the actual width of the gate plus an allowance for hinges and latches. Usually walk gates require 3 3/4″ for hinges and latches and double drive gates require 5 1/2″.
How much gap do you need between double gates?
Double gates will require a throw over gate loop and or drop rods. Allow 1/2 to one inch between double gates .
How do you secure a double gate?
Simple solutions include single-sided locks like a slide bolt that would slide from one gate to the other. Slide bolts and surface bolts are available in many sizes and materials, so you can find what you like.
How does a 2 way gate latch work?
Ring Latches
This type of gate latch is two-sided. They allow operation from both sides of the gate. The outside of the gate (the street side) has a back plate with a ring on it, while the inside of the gate (yard side) features a back plate with a ring which is attached to the arm of the latch.
How do you install double aluminum gates?
How do I keep my aluminum gate from sagging?
If the hinge is still in good condition, tighten it on both the gatepost and gate. A loose hinge bolt can cause sagging gates. Start by finding the lowest point of the gate to adjust the hinge bolts. You have to tighten the top hinge if the gate is lower on the latch side.
How much should be the gap between metal gate and post?
For gates with standard 2×4 framing and 4×4 posts, leave a 1/2- to 3/4-inch space between the latch post and the gate frame. On the hinge side, it will depend on the hardware you use. About 1/4 inch is usually sufficient.
How far off the ground should an aluminum fence be?
Important Information Regarding Your Aluminum Fence Installation. Install your fence 2 to 3 inches off the ground to allow gates to work properly, and to allow maintenance of grass under the fence.
Do you set aluminum fence posts in concrete?
Setting an aluminum fence post in concrete is important–but if you set it in concrete and it’s not perfectly vertical then you’ve got a mess on your hands. You need to check with every post and every panel to make sure that your aluminum fence installation is level.
Does an aluminum fence increase property value?
Aluminum Yards Fences Add Elegance
Metal fencing is the most attractive fencing you can add to your home, meaning it will add the most value when you sell your home. A metal fence automatically adds a prestigious look to your home and increases its curb appeal.
How do I fill the gap under my aluminum fence?
Use decorative stones or river rocks that are between 1-3 inches in diameter to fill the gaps under your fencing. Simply place the appropriate amount of rock into the gaps under fencing and use a bow rake to distribute them evenly over the area, pressing as needed.
How can I hide the gap at the bottom of my fence?
Should you leave a gap under a fence?
Why do you need a space between the pickets and the ground? When wood pickets touch the ground, they absorb moisture, which can lead to swelling or rot. Leaving a space between the pickets and the ground prevents this moisture absorption from occurring, giving you a longer-lasting and nicer-looking fence.
Should a fence follow the ground?
To keep your fence looking nice for a long time, you should keep a 2in (5.08cm) or more gap between your pickets and the ground. This is to prevent moisture absorption and keep your fence from getting damaged by swelling and rot. Leaving the gap allows water to drain from your yard efficiently.