Once you’ve selected the right washing machine outlet box for your situation, it should be installed at a height where the flood level rim (or the top of the drainage outlet) is 32” to 34” above the finished floor.
What is the standard height of a washing machine drain?
In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.
Can a washing machine drain be too high?
A washing machine drain can be too high to pump. Washer drain pumps have a specified power rating, so they can only pump out water at a certain flow rate for a particular drain height. If the drain is too high, the flow rate will be too low to push the water out of the washer, resulting in backflow.
Does washer drain need to be higher than washer?
Elevating A Washing Machine Drain Hose
To be safe, you should always raise the drain hose above the level of the washing machine. This will keep any siphoning to a minimum. You may also take other measures to make sure you receive the best drainage possible.
What height is a washing machine drain and hook up set at? – Related Questions
What is the code for washing machine drain pipe?
According to the Universal Plumbing Code, the standard drain size for a washing machine is 2 inches. The absolute minimum should be about 1 1/2 inches. However, keep in mind that wash load capacities can vary by up to 400% or more depending on the model.
How much drop does a washing machine drain need?
The minimum horizontal slope is 1/4 inch per foot and the max is 3 inches per foot unless vertical. the inlet of the washer drain must be above the height of the washer. This is usually 36 to 38 inches minimum for floor seated washers.
What happens if washing machine drain is too low?
If the drain is too high, the machine won’t be able to propel the water up through the hose. If it’s too low, the water will flow right back into the drum after being pumped out. Either of these scenarios will result in a washer that stays full of soapy, murky water.
How far from drain can washing machine be?
So, how far away can you fit a washing machine drain? You can fit a washing machine drain a maximum of 2.7 m (9 ft) from your washing machine. Washing machines come with standard 1.5 m (4.9 ft) hoses, but you can safely extend them with pipes that are a maximum of 1.2 m (4 ft) long.
What is the minimum height for a standpipe for a washing machine drain?
The standpipe shall extend not less than 30 inches (732 mm) above the weir of the standpipe trap and shall extend above the flood level rim of the laundry tray. The outlet of the laundry tray shall not be greater than 30 inches (762 mm) horizontal distance from the side of the standpipe.
Where should washer drain hose go?
Set Up the Drain Hose
The drain hose will come attached to your washing machine and should feed into either a nearby sink or a standpipe. If you are feeding the drain hose into a sink, attach a plastic hose guide to keep the hose bent downward into the sink without kinking.
Why washing machine drain hose is high?
The drain plumbing should be at least 30″ high to ensure that no water is siphoned. The drain hose must be at least 30″ from the floor and less than 8 feet long in order to operate properly.
How high does a standpipe need to be?
The standpipe for the clothes washer must be trapped. The standpipe height should be at least 18 inches (457 mm) and no more than 42 inches above the trap weir.
Does a washing machine drain need a P-trap?
If they omit the trap and vent, it’s a mistake that can cause problems on two counts. The lack of a P-trap exposes the area to sewer fumes and the lack of venting will cause the drain to run sluggishly and overflow. Washers, like all fixtures, need a trap.
Can a washer and toilet share the same drain?
Your drains are connected – One of the main reasons your toilet gurgles when your washer machine drains is because your washer machine is connected to the toilet drain. This isn’t uncommon. Your washing machine might have been placed in between your toilet and sewer stack.
Does the P-trap have to be lower than drain pipe?
It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally. They both work and have seen it many times. But essentially anything below already creates its own p-trap- so using another is redundant.
Can a P-trap be higher than the drain pipe?
Can a p-trap be installed higher than drain entry? No a P trap works in gravity with a constantly downward flow. Gravity drains dont work uphill unless you pump the fluid.
Does the P-trap have to be at a certain height?
The International Residential Code, under the International Code Council, says that the P-trap must hang at a maximum height of 24 inches below the drain.
Does every P-trap need a vent?
P-traps need vents
1 – They give the sewer gases a place to vent, so they do not build pressure inside your sewer lines.
Why do plumbers use P-traps?
A P-trap is a bend in a drain and waste pipe with a specific purpose. That bend in the pipe contains a pocket of water, which blocks toxic, foul-smelling sewer gases (like methane) from traveling through the pipe into your home.
How do I stop my toilet from smelling like sewer gas?
Add one cup of baking soda to the clogged toilet or slow drain, then wait a few minutes. Follow with two cups of vinegar. Listen for bubbling and sizzling noises to indicate that the mixture is working. Wait another couple of minutes before either flushing the toilet or running water down the drain.