Cycle+Soak is an exclusive feature in Rain Bird Central Control software that allows users to precisely schedule and apply water to be consistent with the infiltration rate of the soil in each specific area around the golf course.
What is cycle and soak on the irrigation system?
Should I cycle soak lawn?
To avoid runoff on the grass or sloped areas of your landscape, you may need to schedule several shorter water cycles in the same day, allowing about 30 minutes in-between for the water to soak in. This is called “cycle and soak” and is easily programmed into your irrigation controller.
How do you cycle soak a lawn?
So, first we soak, allowing that water to move into the soil; and then we wait; then soak again; and maybe even again, until we have applied up to the recommended 1 – 1½ inches of water per week needed for a lawn to remain green during the blazing heat of summer.
What does cycle and soak mean on Rainbird? – Related Questions
How long should I cycle and soak?
As a general rule, 30 minutes is all you need to wait between cycles. Cycle and soak not only eliminates runoff, it provides more water to the roots. The first cycle will break the surface tension of the soil and allow the water to penetrate. The second cycle is absorbed even further into the soil, reaching the roots.
How long should I cycle and soak my lawn?
The cycle and soak method of applying water to the landscape drastically reduces and in some cases eliminates runoff. This method of applying water to the landscape is made up of multiple cycles for each station with 30 to 60 minute for the water to soak into the soil between cycles.
How long is a deep soak for lawn?
Turn off the water for 40 minutes or even an hour to let the water soak in, then water for another 15 minutes or until you see runoff. This may seem complicated at first, but if you take notes on your process, you should learn the unique characteristics of your lawn, your soil, and your turf.
When should I cycle my lawn?
How much water is needed to deep soak an average lawn?
Most lawns need 1 to 1.5 inches of water per week—either from rain or watering—to soak the soil that deeply. That amount of water can either be applied during a single watering or divided into two waterings during the week. Just be sure not to overwater your lawn.
How does Hunter cycle and soak work?
The Cycle and Soak feature allows you to split a station’s run time into more usable, shorter watering durations. This feature is useful when applying water to slopes and tight soils because it automatically applies water more slowly, helping to prevent runoff from occurring.
Should I enable cycle and soak?
The best way to water your lawn is to use the “cycle and soak” method. This method breaks up your watering time into smaller cycles, allowing the water to soak into the soil. If an area is watered too fast for too long, many soils can’t absorb it, resulting in runoff.
Can I water lawn 2 days in a row?
Uniformly applying water helps the soil absorb the water at its own pace. Watering every day is not advised. It should be done 2 to 3 times per week only to prevent a shallow root system. If possible, water during the early morning hours to ensure that the lawn dries entirely before nightfall.
How long does auto soak last?
Once complete, the cycle will continue automatically. AutoSoak must be selected prior to pressing the Start/Pause pad. The AutoSoak time will add an additional 15 minutes, 30 minutes, 1 hour or 2 hours to the overall wash time.
Does Soak cycle rinse clothes?
Wash the load in cool water on the delicate cycle. Depending on what you’re washing, you may want to skip the rinse cycle (Soak is a no-rinse formulation, after all) and save water.
Does the Soak cycle drain?
The soak cycle usually lasts approximately 10-15 minutes. During this cycle the washer will use intermittent agitation and soaking. After time has expired, water will drain, but the washer will not spin.
How do you drain a washer after a Soak cycle?
How to drain a washer filled with water
Try the spin cycle.
Turn off the power and water supply.
Remove and check the drain hose.
Check to see if it will drain with the help of gravity.
Check your machine’s inner workings.
Check the drain pipe.
Drain manually if needed.
Call a service professional.
When should I use soak function in washing machine?
What is ‘Soak Function’ in a Washing Machine?
Soak Function is used to dip clothes in detergent water to remove dirt from the clothes.
Soak – This function is available with wash timer, In 42 min of washing 27 min is soak and 15 min machine will wash the clothes.