The most common reason GE washers stop spinning is a faulty lid switch. The purpose of the switch is to monitor if your washer door is closed, so the main control board knows to let the washer cycle start. This is how to inspect the lid switch: Switch the washer off or unplug it.
How do I get my GE washer to drain and spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
How do you reset a GE washer that won’t drain?
If your washer isn’t working, disconnect it from the power source for one minute. Afterward, plug it back in and quickly lift and lower the lid six times within 12 seconds. And this should reset the motor so you can properly start a cycle.
How do you force a GE washer to drain?
DISCONNECT DRAIN HOSE
Disconnect the drain hose from the wall and allow the water to drain. You may need to have several buckets lined up to catch all the water. Once empty, reconnect the drain hose, move the washer back into place, and turn the power back on.
What causes a GE washing machine to not spin or drain? – Related Questions
What do you do when your washer won’t spin and drain?
Check the Water Level Control
If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
How do you do a hard reset on a GE washer?
How to Reset GE Washer Models
- Shut off the circuit breaks or the fuse to the washer.
- Unplug your washer and wait at least two minutes before plugging it back in.
- If your model has a manual control panel, turn the knob to any setting other than the final spin.
- Plug the unit back in and restore power to your laundry room.
Is there a way to force my washer machine to drain water?
If you have a drain pump filter only, place the shallow container up against the machine, directly under the filter, to catch the water. Turn the knob slowly until water starts coming out. Fill the container, turn the knob off, dump the water into a sink or basin, and repeat until the water has been drained completely.
How do you force a washer to drain water?
How to drain a washer filled with water
- Try the spin cycle.
- Turn off the power and water supply.
- Remove and check the drain hose.
- Check to see if it will drain with the help of gravity.
- Check your machine’s inner workings.
- Check the drain pipe.
- Drain manually if needed.
- Call a service professional.
Why did my GE washer won’t drain?
Kinked or Clogged Drain Hose. A washer’s drain hose carries water out of the washing machine after it’s used. If the hose is kinked or clogged, water won’t be able to flow when the machine is draining. Locate the hose on the back of the machine and inspect it for kinks, gently straightening out the hose if necessary.
How do you drain a locked washing machine?
Turning off the machine at the mains should allow the door lock to cool down, and after a few minutes, you’ll be able to open the washing machine door. The interlocks can take some time to release at the end of the cycle, so be patient. The most common cause is water left in the machine. Try running a spin/drain cycle.
Why wont my washing machine spin?
Here are a few common reasons a washer won’t spin: The washing machine is too full. The load is improperly balanced. The washer itself isn’t balanced correctly.
Can you hard reset a washing machine?
Solutions. Restart it: If you think it might be a digital problem, try the old reset trick. Turn the washing machine off at the powerpoint for at least 60 seconds, and then turn it back on. With a little luck, the master reset should restart the wash programs.
How long does a washing machine stay locked for?
The thermal lock should release the washing machine door about two minutes after the cycle ends. It works by heating up and expanding, so even when the washing machine is switched off the door won’t unlock immediately.
Does unplugging a washing machine unlock it?
These locks are powered by electricity and if you unplug your washing machine, once the residual power drained from the machine the lock should release.
How do you check if your washing machine is blocked?
Next to the pump, you should see a filter cap that covers the actual filter itself. Unscrew the cap and examine the filter for gunk or debris that could be clogging your machine. Rinse it off or use a damp cloth to wipe it down. Test the impeller to make sure it can move freely and isn’t stuck.
Can I override the lock on my washing machine?
Overriding the Locking Mechanism with a Magnet
Placing a separate magnet there will create a stable electromagnetic connection with the solenoid and “trick” the machine into thinking that the lid is closed when it’s really open. Any type of small magnet should do the trick.
How do you reset a washing machine without unplugging it?
Washers Without a Reset Button
For washers with a knob control, turn the dial clockwise to any cycle other than “Final Spin.” With button controls, select any cycle other than “Spin.” Check that the water to the washing machine is on. Turn the breaker back on. Turn the washing machine on.