Your Samsung Front Load Washing Machine comes with shipping bolts inserted into the back of the machine to keep the tub secure during transportation. Suspension system of machine supports the wash tub while it tumbles and spins . Operating machine with locked tub (by shipping bolts) may damage internal parts.
What size are Samsung shipping bolts?
The dimensions of the shipping bolt is approximately, 6 1/8 inches long by 1 inch wide and it is 9 TPI. I hope this helps.
Why is it important to remove shipping bolts Samsung washer?
Before installing the washing machine, it is required that you remove all shipping bolts from the back of the unit. If this has not been done prior to using the machine, the suspension inside of the washing machine will not be able to work.
What happens if you run washer with shipping bolts?
If the four shipping bolts of your machine are still attached to the back of the washer, they will cause a loud noise and vibration during the operation of the machine; which can lead to a permanent damage of the washer.
What are the shipping bolts on a Samsung washer? – Related Questions
What happens if I forget to remove transit bolts from washing machine?
The transit bolts need to be removed when the appliance is being installed. They are designed to hold the drum in a fixed position while being transported. Failure to remove this will void the warranty, so please refer to the appliance manual for additional guidance.
Can I move a washing machine without bolts?
Moving a washing machine without transit bolts will run the serious risk of damaging your machine, so we strongly advise against it. Washing machine transit bolts are a vital piece of equipment required to move your washing machine securely.
What happens if you move front load washer without shipping bolts?
Shipping bolts are required because they protect the drum during the transfer of a washer. A washing machine’s suspension might be damaged by movement, causing it to malfunction.
How many transit bolts does a Samsung washer have?
These bolts “lock” the drum unit in place stopping it from moving. This is a typical example shown below on a Samsung washing machine with three transit bolts fitted, one to the top and two to either side lower down. These bolts must be removed before the washing machine is used.
Are shipping bolts necessary?
The shipping bolts keep the tub secure during a move and reduce the amount of vibration that could damage the suspension. If you do not have the necessary shipping bolts, you can purchase them through an appliance repair center.
What happens if you move front load washer without shipping bolts?
Shipping bolts are required because they protect the drum during the transfer of a washer. A washing machine’s suspension might be damaged by movement, causing it to malfunction.
Can you damage a washing machine by moving it?
A washing machine’s tub has a suspension system that allows the drum to move freely. This system prevents damage from vibrations when the drum spins or agitates. Moving puts a great deal of wear and tear on a washer’s suspension system.
Do you use washers with flange bolts?
Washers. Addition of steel washers to a fastener system is recommended to improve translation of torque input into bolt preload. Washers provide a smooth bearing surface, reducing friction between nut and flange.
Do you always need a washer with a nut?
Washers are important. They ensure that a nut is installed properly and prevent softer materials from damage by distributing the pressure over a greater surface area. Are washers necessary? Washers are not always necessary but it is common practice to use them anyway.
Is it OK to stack washers on a bolt?
It is not a good practice to stack washers in a fastener joint. Each stacked element acts like springs in series, consequently, fastener joint stiffness would be compromised.
What goes first lock nut or washer?
When used correctly, a lock washer will hold the nut or other threaded fastener in place. To help it accomplish this, put the lock washer on first, below the fastener. If your project calls for other washers or hardware elements, they should go on before the lock washer so that it can hold them in place.
Should washer go under nut or bolt?
The lock washer should be placed under your threaded fastener – i.e., underneath a nut or the head of a screw or bolt. In assemblies where you have a nut and a bolt, the washer should be placed between the nut and the head of the bolt. You can then tighten the threaded fastener as normal.
Can I use a nut and washer instead of a flange nut?
Using a hex nut and washer instead of a flange nut introduces an additional inner interface, and the associated additional preload loss due to embedding and relaxation in that interface.
Why is a washer installed under a nut?
Washers have traditionally been used to protect the joint surface from damage during the tightening process and to distribute the load under the bolt head and nut. The stress under the face of a standard hexagon headed nut can result in indentation into standard strength steel surfaces.
Should washer be bigger than bolt?
– Washers must always be larger than exact diameter of screw. Determining the Diameter: Both nuts and washers are sized by the fasteners they fit.