How do you put a Maytag washer in diagnostic mode?

How do I put my Maytag Bravos in test mode?

How do I reset my Maytag washer control board?

The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.

Is there a reset button for a Maytag Bravos XL?

Maytag washers do not have a reset button, but it is possible to reset them by pressing certain buttons in a particular combination. This is the simplest method to try: Press power/cancel first. Next, pick a fresh cycle to run.

How do I run F12 diagnostics?

At the Dell logo, press the F12 key several times until the One Time Boot Menu appears. On the boot menu screen, select the Diagnostics option and press Enter (Figure 1). The diagnostic test begins.

What is an F5 code for a Bravos XL washer?

Did you receive a F5 E2 lid lock alert? The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.

What does a code F6 and E2 code means in a Bravos XL Maytag washer?

The F6 E2 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.

What does E2 and f2 mean on a Maytag washer?

If this code appears on your dishwasher display, it means that there is a communication failure between the electronic control and the touchpad.

What does E3 and F6 mean on a Maytag washer?

The F6 E3 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.

What does E2 mean on Maytag washing machine?

An E2 Error code indicates that the washer is still draining after 8 minutes. Check the following: Check that the drain hose is not more than 391 ⁄3″ (100 cm) from the floor. Remove any clogs from the drain hose.

What does F2 and E3 mean on a Maytag washer?

The F2 E3 alert indicates there may be an issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait two minutes, then plug back in.

What does E3 mean on a Maytag washer?

The E3 error means that the control board is detecting current going to the motor, but the motor won’t turn properly. If the error code comes up all the time as soon as you press the power on button, then it means your control board is bad and reading incorrectly.

How do I fix E2 error?

“E2” – Low Pressure: The pressure of the compressor is too low. The ‘Error’ LED will be on. Solution: Clean filters & coils. Verify Power.

What does E2 error code?

The E1 or E2 error code is an Auto-Stop Protection Error, indicating an issue detected by a sensor. This error code will require service. The E3 error code displays when an Abnormal Operation Protection Error has occurred, and activates to protect the unit from damage.

How do I fix E3 error on my washing machine?

E3 – Unbalanced alarm

This could be caused by the washer being too tightly packed, or clothing not distributed evenly. This will usually occur during the spin cycle. Stop the spin cycle. Remove several items, rearrange load evenly around the washplate, and restart the Spin cycle.

What does E02 error mean?

The thermostat will display error code E02 if the password to the home router was entered incorrectly. The thermostat will automatically progress to the Wi-Fi Set Up screen after 30 seconds. Was this article helpful?

Why is my washer saying E02?

E02. You’ll see this error code if/when the washing machine fails to fill. It indicates there could be a blocked fill hose, or an issue with either the water supply or the valves.