How do you fix a Whirlpool washing machine that won’t drain?
•
Drain residual water into a bucket and inspect the hose for clogs. Remove any visible blockages with a straightened wire hanger or pliers. If no blockages are visible, disconnect the hose from the standpipe or sink to inspect for clogs. Reconnect the hose at the standpipe or sink and washer.
How do I manually drain my Whirlpool washer?
You may want to turn off the water supply to the hot and cold hoses as an extra precaution. Then, disconnect the drain hose from the pipe and hold it above the washing machine, so water doesn’t spill out. Grab your bucket and carefully lower the drain hose into it and let gravity do the work.
Why did my washer not drain?
A washing machine not draining can have multiple causes, including a clogged or jammed drain hose or a broken pump, lid switch, or belt. No matter the culprit, you need to drain the water from the washing machine before diagnosing the issue or doing any work to remedy the situation.
How do you reset a washer that won’t drain?
Unplug your washer for about one minute.Then, plug the appliance back in.Open and close the door six times in 12 seconds to tell the computer to reset everything.
How do you fix a Whirlpool washing machine that won’t drain? – Related Questions
How do you force a washer to drain water?
How to drain a washer filled with water
Try the spin cycle.
Turn off the power and water supply.
Remove and check the drain hose.
Check to see if it will drain with the help of gravity.
Check your machine’s inner workings.
Check the drain pipe.
Drain manually if needed.
Call a service professional.
Why won’t my Whirlpool washer drain and spin?
Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose.
How do you reset a washing machine drain?
Unplug your washer for about one minute.Then, plug the appliance back in.Open and close the door six times in 12 seconds to tell the computer to reset everything.
Why is my washing machine not spinning and emptying?
The drainage is poor
Normally, your washing machine won’t go into a spin cycle until it’s been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.
Why won’t my washer spin but drain?
The washing machine drains but won’t spin. A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure.
How do I manually reset my washing machine?
How do you reset a washing machine drain?
Unplug your washer for about one minute.Then, plug the appliance back in.Open and close the door six times in 12 seconds to tell the computer to reset everything.
Is there a reset button on a washing machine?
Reset your washing machine
There really isn’t a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.
How do I know if my washing machine drain pump is clogged?
Remove the drain hose by unscrewing the clamps holding it to the pump outlet. Look for blockages inside the hose, says Family Handyman. If you don’t see any, the pump may be blocked or faulty. To check it, you have to disconnect the belt connecting it to the drive motor.
How do I know if my drain tube is clogged?
There is water coming back out of the pipe which is a dead giveaway. But also there is water pooled up all around it which is also a giveaway. If you see a water stain around your underground drain, that is also a sign that it is clogged.
How do I know if my Whirlpool drain pump is bad?
A common complaint is that the water in the washing machine drum will not drain, or that the washing machine has stopped mid-cycle with it still full of water. Another common issue is that the washing machine drum will not spin, or it won’t drain properly.
How do you unclog a pump on a Whirlpool washer?
Why won’t my washer drain and spin?
Washer Won’t Drain
Malfunctioning drain pump – A small object or article of clothing may have created an obstruction in the drain pump, or a damaged impeller could cause the pump to fail mechanically. If the pump doesn’t appear to be damaged and is free of obstructions, it’s possible the pump has failed electrically.
How do you test a whirlpool drain valve?
The check valve is located underneath the dishwasher, just before the drain hose. It’s a one-way valve, allowing water to drain but not return to the dishwasher. Remove the drain hose from the dishwasher (remembering to put a drain pan underneath) and check to make sure the valve is clean and opens correctly.
How do I know if my water inlet valve is clogged?
Signs pointing to a faulty inlet valve include:
Leaks that fill the dishwasher when it’s off.
Inadequate water for a cycle.
A bad inlet valve can lead to leaks from the dishwasher onto the kitchen floor.
Most inlet valve malfunctions stem from a defective seal or solenoid failure.