The UE error code sometimes appears because the washer is too full for the control board to redistribute the load during the rebalance routine. In this case, remove some garments and restart the cycle in Rinse/Spin mode. In the future, loosely place items in the basket; don’t pack down the load and add more garments.
How do I fix the UE on my washing machine?
The uE/UE code indicates that the washer is attempting to balance the load, which may be the result of the unit not being leveled correctly or the load itself.
Run rinse and spin cycle without load.
Empty the drum completely.
Power the unit on.
Select the RINSE AND SPIN cycle.
Press start.
How do you fix UE?
The UE Error Code means you have an unbalanced load.
There are 3 easy fixes.
Check the washer legs. All four should rest evenly on the ground with nothing underneath them.
Redistribute the wash.
Try turning it off and on.
How do I reset my Kenmore washer?
How do you fix a UE code on a Kenmore washer? – Related Questions
Does unplugging a washer reset it?
Reset your washing machine
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.
Where is the reset button on a Kenmore?
Is there a reset button on a Kenmore refrigerator? Answer: A Kenmore refrigerator lacks a reset button that specifically manages the compressor’s power. But ice maker switches are available. with their power button.
How do you force a washing machine to reset?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do I reset the control panel on my washing machine?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I reset my top washer?
Motor Reset Procedure:
Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.
How do I reset my washing program?
Programmable Washing Machine
In certain models, turn the knob to reset with the power button “Off.” Select the desired program. Press the power button to restart the washer. In other cases, if the machine has a “Cancel” button, push it to clear the error and then push the “Pause” or “Stop” button to reset it.
Why won t washer spin and drain?
Top reasons washers won’t spin or drain
The coupler can wear out over time or fail, especially if the tub is consistently overloaded. Similarly, a drive belt can wear out, break, or slip on the pulleys. In both cases, the tub won’t spin until the worn coupler or damaged belt is replaced.
How long should a washing machine last?
The average life of a washing machine ranges from 10 to 13 years, although some brands can manufacture washing machines with an even longer lifespan than the average appliance.
Why won’t my washing machine finish its cycle?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
How do you manually drain a washing machine?
If you have a drain pump filter only, place the shallow container up against the machine, directly under the filter, to catch the water. Turn the knob slowly until water starts coming out. Fill the container, turn the knob off, dump the water into a sink or basin, and repeat until the water has been drained completely.
Why does my Kenmore washer stop mid cycle?
If the water inlet valve fails, the washer will continue waiting for the water to enter the washer, causing it to stop mid-cycle. To determine if the water inlet valve is defective, use a multimeter to test it for continuity. If the water inlet valve does not have continuity, replace it.
Why is my Kenmore washer always off balance?
One or more of the suspension springs might be broken. The suspension springs help to absorb the movement of the washer tub. If a suspension spring breaks, the tub might become unbalanced, causing it to shake and vibrate during operation. Inspect the suspension springs to determine if any of the springs are broken.
How do you fix a Kenmore washer that won’t drain or spin?
What causes a Kenmore washing machine not to spin out?
If the clutch is worn out, it may prevent the tub from spinning. If the clutch band kit is worn out, replace it. The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning.