How do you fix a UE code on a Kenmore washer?

The UE error code sometimes appears because the washer is too full for the control board to redistribute the load during the rebalance routine. In this case, remove some garments and restart the cycle in Rinse/Spin mode. In the future, loosely place items in the basket; don’t pack down the load and add more garments.

How do I fix the UE on my washing machine?

The uE/UE code indicates that the washer is attempting to balance the load, which may be the result of the unit not being leveled correctly or the load itself.

Run rinse and spin cycle without load.

  1. Empty the drum completely.
  2. Power the unit on.
  3. Select the RINSE AND SPIN cycle.
  4. Press start.

How do you fix UE?

The UE Error Code means you have an unbalanced load.

There are 3 easy fixes.

  1. Check the washer legs. All four should rest evenly on the ground with nothing underneath them.
  2. Redistribute the wash.
  3. Try turning it off and on.

How do I reset my Kenmore Elite washer?

How do you fix a UE code on a Kenmore washer? – Related Questions

Does unplugging a washer reset it?

Reset your washing machine

What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.

How do I reset my Kenmore washer control board?

How do you force a washing machine to reset?

If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

Where is the reset button on a Kenmore?

Is there a reset button on a Kenmore refrigerator? Answer: A Kenmore refrigerator lacks a reset button that specifically manages the compressor’s power. But ice maker switches are available. with their power button.

How do I put my Kenmore Elite washer in diagnostic mode?

3 Answers
  1. With the washer empty, close the door.
  2. Push “control/on” or “Start”
  3. Select “Drain/Spin”
  4. Select “No Spin” by pressing SPIN SPEED touchpad.
  5. Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
  6. C:00 should light up and begin the diagnostic.

How do you force a washing machine to reset?

If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

How do I reset the control panel on my washing machine?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

Where is the reset button on a Kenmore?

Is there a reset button on a Kenmore refrigerator? Answer: A Kenmore refrigerator lacks a reset button that specifically manages the compressor’s power. But ice maker switches are available. with their power button.

Why is my Kenmore Elite washer not starting?

If Your Washing Cycle Won’t Start, Check the Lid Switch in Your Kenmore Washer. If your washer won’t start or progress through the cycle, check the washer lid switch lid. When your appliance doesn’t think the lid is properly shut, it won’t start the next step in the washing cycle.

When I press start on washing machine nothing happens?

You should check the outlet to make sure it’s working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated. Sometimes it’s as simple as opening and closing the door to reset the washer.

How do I run diagnostics on my Kenmore Elite washer?

3 Answers
  1. With the washer empty, close the door.
  2. Push “control/on” or “Start”
  3. Select “Drain/Spin”
  4. Select “No Spin” by pressing SPIN SPEED touchpad.
  5. Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
  6. C:00 should light up and begin the diagnostic.

Why is my washing machine on but not starting?

If the lights on your washing machine come on but it won’t begin the washing cycle, it’s clear that power is going through to it. Therefore, the problem lies with the appliance itself. For safety reasons, modern washing machines are programmed to stop going into a cycle if the door is not shut properly.

Why does my washer turn on but not spin?

Here are a few common reasons a washer won’t spin: The washing machine is too full. The load is improperly balanced. The washer itself isn’t balanced correctly.

Why won’t my washing machine finish its cycle?

Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.

Why is my washer not spinning but it will drain?

The washing machine drains but won’t spin. A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure.

How do I know if my washer drain hose is clogged?

Start by running your washer through a drain cycle. Observe the washing machine as it pumps water into the hoses and up into the standpipe. If you see water back up and out of the standpipe, your washer’s drain is most likely the issue.

Leave a Comment