How do you fix a LG washer that won’t drain?

•

  1. Check the Door Lock Switch. Washers will not run if the door or lid is not closed.
  2. Rebalance the Load. Another simple problem that can stop the washer from draining is an unbalanced load.
  3. Drain Your Washer Manually.
  4. Clean the Drain Filter.
  5. Inspect the Drainage Hose.
  6. Check That the Drain Pump Is Working.

How do I get my LG washer to drain?

Press the POWER button to turn the washing machine off and remove the plug from the outlet. Locate the service panel on the bottom-left corner of the unit and open it. Unclip the drain hose and remove the plug from the drain hose to drain the water remaining inside the wash tub.

Why is my LG front load washer not draining?

A clogged pump can result in an LG washer not draining completely or at all. This can happen more easily if the drain pump filter is also clogged. Refer to your user manual to determine how to access the drain pump and inspect it for clogs. Most are located on the bottom of the washer behind a rear panel.

How do I force my LG top load washer to drain?

Force drain the unit by starting a cycle and pausing it.

If you don’t have SPIN ONLY

  1. Power the unit ON.
  2. Select a cycle.
  3. Press START/PAUSE button to START the cycle.
  4. Allow a few minutes to pass so the cycle begins.
  5. Press the START/PAUSE button to PAUSE the cycle.
  6. Run an empty wash cycle to see if issue occurs again.

How do you fix a LG washer that won’t drain? – Related Questions

Can you force an LG washer to drain?

For LG front load washers, turn the unit on and without touching the selector dial move to the spin speed selection button. Next, press the button until you see your desired spin speed highlighted. Then press the Start button. The unit will drain any excess water before it spins.

Why is my washer full of water and won’t drain?

The most probable cause is a clogged pump filter. The pump filter should be cleaned every three months or when it’s clogged. This filter is installed to catch foreign objects like buttons or coins, and to prevent these items from entering the drain hose.

How do you manually drain a top loader?

How to Manually Drain a Top-Loading Washing Machine
  1. Step 1: Turn off the power and lay down towels.
  2. Step 2: Locate the drain hose at the back of the washing machine.
  3. Step 3: Drain the water.
  4. Step 1: Turn off the power and lay down towels.
  5. Step 2: Locate the drain hose.
  6. Step 3: Drain the water.
  7. Step 4: Scrub the filter.

Is there a way to force my washer machine to drain water?

Try the spin cycle

If your machine allows it, try manually setting it to the spin cycle and running it to see if it drains. You may also try restarting the entire wash cycle to see if it works.

How do you fully drain a top load washer?

If your top-loading washer did not drain by unblocking the drain hose or initiating drain prompts, siphon the water into buckets with a hose.
  1. Open the Lid. Open the washing machine lid.
  2. Unplug the Washer and Turn Off the Water.
  3. Remove the Clothing.
  4. Place Buckets.
  5. Set Up a Water Siphon.
  6. Drain the Washing Machine Drum.

How do you fix a washing machine that won’t drain?

What to Do When Your Washing Machine Won’t Drain
  1. Perform a Master Reset. Unplug your washer for about one minute.
  2. Test the Lid Switch Assembly.
  3. See if the Drain Hose is Kinked.
  4. Check the Drain Hose or Pump for Clogs.
  5. Clean out the Coin Trap.
  6. Check the Water Level Control.
  7. Schedule Washing Machine Repair.

How do you drain a washer that won’t drain?

Remove the Front Panel Screws

Start by unplugging the machine and emptying the water. Bail the water out of the tub. Pro tip: Drain the tub using gravity by placing the washer drain hose on the floor near the drain or in a bucket. Clamp the hose to prevent any remaining water from running out.

How do I know if my washing machine drain is clogged?

Start by running your washer through a drain cycle. Observe the washing machine as it pumps water into the hoses and up into the standpipe. If you see water back up and out of the standpipe, your washer’s drain is most likely the issue.

Why will my washer spin but not drain?

The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.

How do I know if my drain pump is blocked?

Remove the drain hose by unscrewing the clamps holding it to the pump outlet. Look for blockages inside the hose, says Family Handyman. If you don’t see any, the pump may be blocked or faulty. To check it, you have to disconnect the belt connecting it to the drive motor.

How do you test a washing machine drain pump?

How much does it cost to repair a washing machine drain pump?

Pump Replacement

Accessing and replacing your washing machine’s pump is a bit more complex than some easier repairs and maintenance tasks, such as unclogging the drain or cleaning and deodorizing the tub. Most new washing machine pumps cost between $30 and $40, and you can expect to pay around $300 for labor.

How do you reset a washing machine drain?

Unplug your washer for about one minute. Then, plug the appliance back in. Open and close the door six times in 12 seconds to tell the computer to reset everything.

Leave a Comment