How do I turn on the load and go feature on my Whirlpool washer?

What does load and go mean on my Whirlpool washer?

What is a Load & Go™ Dispenser? The Load & Go™ Dispenser featured in select Whirlpool® Washing Machines lets you skip adding detergent to every load. The Load & Go™ Dispenser is designed to store enough detergent for 20–40 loads of laundry,1 depending on the washer model.

How do I change the settings on my Whirlpool washer?

Press and hold the Programme button for at least 3 seconds. Turn the knob to select the setting which you want to change; confirm it by pressing the knob. Turn the knob to adjust the setting; confirm by pressing the knob.

How do I get the Control Lock off my Whirlpool washer?

If you do not see the 3-2-1 countdown and are unable to de-activate Control Lock, try pressing the POWER button first, then touch and hold 3 seconds to de-activate control lock. If this does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and try again.

How do I turn on the load and go feature on my Whirlpool washer? – Related Questions

Can you bypass the lock on a Whirlpool washer?

Tip: The lid lock mechanisms on some washers are heat-activated, which means overriding them is as simple as letting them cool off. Let the washer sit unplugged for about 10 minutes, then try lifting the lid. If it opens, you’re all set.

How do you bypass the lock switch on a washing machine?

Why does my Whirlpool washer say control locked?

There is no Error – Control Lock is activated

If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.

How do you bypass the lid lock switch on a Whirlpool washer?

Where is the control lock on a Whirlpool?

How do I reset my Whirlpool control panel?

Some models require you to shut off the power to the dishwasher either by unplugging it or shutting off the circuit breaker. Others are reset by pressing and holding the Start/Reset button on the control panel, then waiting a few moments before attempting to start a wash cycle.

Is there a reset button on a Whirlpool?

How do I reset my Whirlpool load and go?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.

How do I manually reset my washing machine?

If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

How do I reset my top load washer?

Motor Reset Procedure:
  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
  3. The motor has now been reset and is ready for you to start a cycle.

How do I reset the control panel on my washing machine?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

Is there a way to factory reset a washing machine?

Reset your washing machine

There really isn’t a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.

What are the most common problems on a Whirlpool washing machine?

Here are seven of the most common problems on a Whirlpool washing machine and potential fixes for them.
  • Washer Making Unusual Noises.
  • Washer Won’t Start.
  • Washer Lid Won’t Lock.
  • LD Error Code Appears.
  • Washer Leaves Deposits on Dark Clothes.
  • Washer Has a Burned Plastic Odor.
  • Rust Spots Appear on Washer Lid.

Leave a Comment