What is a Load & Go™ Dispenser? The Load & Go™ Dispenser featured in select Whirlpool® Washing Machines lets you skip adding detergent to every load. The Load & Go™ Dispenser is designed to store enough detergent for 20–40 loads of laundry,1 depending on the washer model.
How do I change the settings on my Whirlpool washer?
Press and hold the Programme button for at least 3 seconds. Turn the knob to select the setting which you want to change; confirm it by pressing the knob. Turn the knob to adjust the setting; confirm by pressing the knob.
How do I turn off LOC on Whirlpool?
If you do not see the 3-2-1 countdown and are unable to de-activate Control Lock, try pressing the POWER button first, then touch and hold 3 seconds to de-activate control lock. If this does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and try again.
How do I turn on my Whirlpool washer load and go? – Related Questions
How do I get my washer off of control lock?
On a Front Load Washer, depending upon the model, to Lock or Unlock the washer controls you press and hold either the Control Lock or Light-Control Lock pad for 3 seconds. A sound is made to indicate the Lock/Unlock status. Some older Front Load Washer models simply had a Lock button.
Why does my Whirlpool front load say LoC?
If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.
Why is my Whirlpool washer stuck on control lock?
The most common cause of a Whirlpool washer door being locked and not being able to open is a faulty lid switch (including the striker). The door switch locks and unlocks your door depending on which stage your wash cycle is at. When it becomes defective, your washer door may not unlock when it’s supposed to.
How do I turn off the key lock on my Whirlpool oven?
What does Loc on Whirlpool stove mean?
LOC means the control panel is locked. Per the Use and Care Guide: 1. Check that the oven and cooktop are off. 2. Press and hold CONTROL LOCK for 3 seconds.
Where is the control lock on a Whirlpool?
Can you bypass the lock on a Whirlpool washer?
Tip: The lid lock mechanisms on some washers are heat-activated, which means overriding them is as simple as letting them cool off. Let the washer sit unplugged for about 10 minutes, then try lifting the lid. If it opens, you’re all set.
How do I reset the control panel on my Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP.Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
How do I reset my Whirlpool control panel?
Some models require you to shut off the power to the dishwasher either by unplugging it or shutting off the circuit breaker. Others are reset by pressing and holding the Start/Reset button on the control panel, then waiting a few moments before attempting to start a wash cycle.
How do you do a hard reset on a dishwasher?
You can reset your dishwasher by unplugging it from its power source for one minute and then plugging it back in. If it’s hardwired to a power supply or the plug is not easy to access, turn off the breaker for the dishwasher on your home’s electrical panel and turn it back on after one minute.
What is the most common problem with a Whirlpool dishwasher?
Most common problems with Whirlpool dishwashers
The dishwasher does not drain properly. The detergent cup is not working properly. The dishwasher is not filling with water. The dishwasher door is leaking.
Does my Whirlpool dishwasher have a reset button?
Press the “Heated Dry” button, followed by pressing the “Normal” button, and then press both buttons again in quick succession. Once you’ve pressed the two buttons twice, your dishwasher should go into a diagnostic mode, which will cause it to reset.
How do you cancel a cycle on a Whirlpool dishwasher?
To cancel a delay and the cycle:
Press Cancel/Drain pad once to drain and turn off the dishwasher.
Press Cancel/Drain pad twice to turn off the dishwasher without draining.
How do you unlock the controls on a Whirlpool dishwasher?
Press and hold the designated control lock button for your model for 3 seconds. The location of the control lock button may vary depending on your model. Refer to the Owner’s Manual for the control lock button location for your model. The light will turn off and the control will be unlocked.
What does the reset button do on a dishwasher?
Dishwashers with an OPTIONS RESET button (introduced on some models in 1993 and was used for several years after) allow you to turn off the wash heat boost function and the heated dry function.