To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do you replace the control board on a GE top load washer?
How do you change a GE control board?
Why won’t my GE washer agitate or spin?
If the washer is not agitating, you may need to reset your washer motor. If your washer senses a power spike, an unbalanced load or disruption in power, it will send a fault code to the motor and may require the motor to be reset.
How do I reset my GE washer control board? – Related Questions
How do you fix a GE top load washer that won’t spin?
How to Fix a GE Washer Not Spinning
This guide covers all major GE washer models, including:
Step 1 – Inspect the lid switch.
Step 2 – Inspect the drive belt.
Step 3 – Inspect the motor coupling.
Step 4 – Inspect the door latch.
Step 5 – Inspect the motor control board.
Step 6 – Inspect the clutch.
Step 7 – Inspect the rotor.
What causes a GE washing machine not to spin?
Clean the filter of any debris and then replace it, reassembling the washer. A clogged household drain can also cause water to stand in the washer and prevent the spin cycle from starting. Contact a plumber to address the issue.
How do you fix a washer that won’t agitate or spin?
Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. The motor coupling connects the motor to the washer transmission. If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission.
How do I reset my GE agitator?
Unplug the washer or shut off the washer circuit breaker or fuse. Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting. Restore the power.
What causes a washing machine to stop agitating?
Your washer may not be agitating due to worn-out directional cogs. Check to see if your machine’s agitator has two parts, allowing it to move the water left or right. If it does, and the cogs are damaged, the upper part of the agitator won’t properly connect to the bottom part.
How do I force my GE washer to spin?
Can you hard reset a washing machine?
Solutions. Restart it: If you think it might be a digital problem, try the old reset trick. Turn the washing machine off at the powerpoint for at least 60 seconds, and then turn it back on. With a little luck, the master reset should restart the wash programs.
How do you do a master reset on a washing machine?
How do I reset my top washer?
Motor Reset Procedure:
Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.
How do you reset a washing machine sensor?
How do you put a washing machine in diagnostic mode?
How do you diagnose washer control and program problems?
How to Diagnose Washing Machine Control and Program Problems
What You Will Need:
Switch Off Your Appliance.
Check 1 – Turning The Machine On.
Check 2 – Recognise That It Is Filled With Water.
Check 3 – Heating The Water & Proceed With Wash Cycle.
Check 4 – Drain The Water & Proceed With Rinse Cycle.
How do you bypass a washing machine sensor?
Here is a simple way to do this:
Let us say you have 2 lbs of clothes.
Add the 2 lbs of clothes in the washtub.
Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric.
Start the wash cycle.
You have successfully bypassed water level sensor.
How do you trick a washing machine lid switch?
Tip: The lid lock mechanisms on some washers are heat-activated, which means overriding them is as simple as letting them cool off. Let the washer sit unplugged for about 10 minutes, then try lifting the lid. If it opens, you’re all set.