Are gas furnace igniters universal?
This universal ignitor is a replacement part for use in gas-fired appliances like furnaces, water heaters, and boilers, compatible with over 150-OEM models.
How often should furnace ignitor be replaced?
How Often Should a Furnace Ignitor Be Replaced? On average, furnace ignitors will last about four to seven years. This depends upon how well maintained the system is. After the seven-year mark, you should replace it.
Are all hot surface ignitors the same?
Not All Hot Surface Igniters are The Same.
How do I know if my hot surface ignitor is bad? – Related Questions
Why do furnace ignitors fail?
Due to safety reasons, if a furnace’s air filter has become clogged, the furnace will no longer ignite. So, if your furnace is failing to ignite, it’s a good idea to check the air filter. If it looks clogged up, then this is probably the source of the problem.
How long do hot surface igniters last?
Under normal operating conditions, a hot surface igniter will last 3-5 years. During the heating season, the hot surface igniter can go through a tremendous amount of use.
Are furnace hot surface ignitors interchangeable?
Most ignitors are interchangeable as long as they fit in the furnace space provided. Select your ignitor by looking at the one you have, and comparing it to the photos of ignitors here; select the one most similar.
What should a hot surface ignitor ohms be?
A good silicon nitride hot surface ignitor will have a resistance of 30 to 75 ohms. Greater than 75 ohms indicates a failing or failed hot surface ignitor. If you get 0 or ∞ or no reading at all, it mean that the resistance is broken, so the igniter is broken and should be replaced.
What are the types of igniters?
Igniters for SRMs are basically of two types, viz., Pyrogen igniters used for large rocket motors of ballistic missiles, and Pyrotechnic Igniters used for small rocket motors.
Is hot surface ignitor same as flame sensor?
As soon as combustion has been initiated, electricity ceases to flow to the hot surface igniter. For optimum safety, a hot surface ignition system utilizes what is known as a flame sensor.
Can I touch hot surface igniter?
Some service technicians may be surprised to learn that the silicon carbide element of a hot surface igniter (HSI) can be handled without damage. However, it is better and safer to handle the igniter by the ceramic holder.
Can you repair a furnace ignitor?
If you are certain that the problem lies with the furnace ignitor, then you need to get it for repair or replacement. There are two ways to do this. You can either use a socket wrench to remove the furnace ignitor, or you can use a hair dryer to heat the furnace up.
How many volts does a furnace ignitor need?
You should have 24 to 28 volts from each terminal to ground. On most furnaces the ignitor will not glow unless all the safety controls (limit, rollout switch/switches, pressure switch) are closed. If a limit or rollout switch is open, you can have an overheating problem and a possible dangerous condition.
Can a furnace ignitor be cleaned?
To clean the unit, rub the probe with an emery cloth or fine steel wool to remove the burnt carbon. When it looks clean replace the ignitor, hook up the wires and restore power to the furnace. The ignitor can be tested by turning up the thermostat to get the gas furnace started.
How many ohms Should a furnace ignitor have?
Resistance should be between 37-68 ohms. If the igniter and the surrounding air are at about 70°F and the igniter wires are not connected to any other electrical components, the resistance of the igniter should not exceed 75 ohms. If it does, the igniter should be replaced.
Do furnace ignitors go bad?
Your furnace won’t run: The most obvious sign that your ignitor is bad is that it won’t ignite, and this generally manifests itself in your furnace failing to run when you activate it. One word of caution, though: this can also be caused by other issues, some of which are electrical.
How much does it cost to have a furnace ignitor replace?
Your furnace’s ignitor plays a critical part in the start-up process. As its name suggests, it ignites the gas your furnace turns to heat. The average cost to repair or replace an ignitor is $150–$300.
How do I reset my furnace ignitor?
Resetting The Ignitor
Once the power is off you can remove the burner door to reveal the ignitor. Turn this to “off” and leave it off for at least 5 minutes. After this time, turn the ignitor back to the “on” position and replace the burner door. You can then turn the power source back on and restart the furnace.
How do you test an ignitor?
Why would an igniter stop working?
Whether it’s grease buildup or food crumbs, one of the most common causes for a gas burner that has trouble igniting is debris blocking gas flow to the igniter.