Can you move a washing machine without transit bolts?
Moving a washing machine without transit bolts will run the serious risk of damaging your machine, so we strongly advise against it. Washing machine transit bolts are a vital piece of equipment required to move your washing machine securely.
What size are Samsung shipping bolts?
The dimensions of the shipping bolt is approximately, 6 1/8 inches long by 1 inch wide and it is 9 TPI. I hope this helps.
Do Samsung washing machines have transit bolts?
Your Samsung Front Load Washing Machine comes with shipping bolts inserted into the back of the machine to keep the tub secure during transportation.
Are washing machine shipping bolts universal? – Related Questions
Why is my Samsung washer shaking violently?
This can happen when the four washing machine legs are not all making secure contact with the ground, or if a large bulky item or huge amount of laundry is in the washing machine. If you just got your front load washer, but didn’t remove the shipping bolts, then it will shake a lot.
Do Samsung top load washers have shipping bolts?
How many transit bolts does a Samsung washer have?
These bolts “lock” the drum unit in place stopping it from moving. This is a typical example shown below on a Samsung washing machine with three transit bolts fitted, one to the top and two to either side lower down. These bolts must be removed before the washing machine is used.
Why is it important to remove shipping bolts Samsung washer?
Before installing the washing machine, it is required that you remove all shipping bolts from the back of the unit. If this has not been done prior to using the machine, the suspension inside of the washing machine will not be able to work.
How do you put a transit bolt on a Samsung washing machine?
How do I remove Samsung shipping bolts?
What happens if I forget to remove transit bolts from washing machine?
The transit bolts need to be removed when the appliance is being installed. They are designed to hold the drum in a fixed position while being transported. Failure to remove this will void the warranty, so please refer to the appliance manual for additional guidance.
What happens if you run a washer with shipping bolts?
If the four shipping bolts of your machine are still attached to the back of the washer, they will cause a loud noise and vibration during the operation of the machine; which can lead to a permanent damage of the washer.
What happens if you leave transit bolts in washing machine?
The bolts can rip sections off the outer tank, tear through the outer casing and cause massive damaging vibrations to be sent through the room in which the washing machine is installed. In other words, by not doing as instructed you risk major damage to your washing machine.
Why do shipping bolts make washer shake?
If the drum does not wobble, the shipping bolts are likely still holding it in place, which can cause the whole washer to shake instead of just the drum inside.
Can you reuse one time use bolts?
Reuse of a structural bolt is permitted only when a bolt has not been stressed past its yield point. A quick way of telling if a F3125 Grade A325 bolt has yielded is to attempt to screw a nut onto the bolt.
Do all new washing machines have transit bolts?
All new washing machines are fitted with a transit bolts to protect the machine against damage in transit. Transit locks and bolts must be removed before you use your appliance.
Can you buy washing machine transit bolts?
If you do not have the transit bolts, check with the local appliance store where the washing machine was originally purchased. The store will be able to get some or order some for your specific machine.
Can I use a washer instead of a flange bolt?
The effect of using washers instead of flanged nuts and bolts is to increase the number of interfaces within the joint. Since each face will sustain an embedding loss, the net effect of using washers is to increase the loss of bolt tension due to this effect.
Do transit bolts stop the drum spinning?
Transit bolts are meant to prevent the washing drum for rotating, vibrating, moving while the machine is in transit or transport. These bolts must be removed once machine is installed and ready to be operated.
How do I stop my bolts from vibrating loose?
Nylon or metal inserts inside a nut (sometimes called a “lock nut”) can add extra friction to prevent loosening. A related idea is to fit a spring inside the nut, which firmly grasps the bolt threads and is designed to move in the opposite direction of the nut if vibration or other forces cause it to unwind.