This usually indicates the washer took too long to pump the water out. There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If the washer drains properly, then the clog has likely cleared.
How do I get my GE washer to drain and spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
What would cause a washing machine not to drain and spin?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken. If a washer won’t drain or spin, the fix is simple if you’re even just a little bit handy with tools.
How do you reset a GE washer that won’t drain?
If your washer isn’t working, disconnect it from the power source for one minute.Afterward, plug it back in and quickly lift and lower the lid six times within 12 seconds. And this should reset the motor so you can properly start a cycle.
Why is my GE washer not draining or spinning? – Related Questions
How do you do a hard reset on a GE washer?
How to Reset GE Washer Models
Shut off the circuit breaks or the fuse to the washer.
Unplug your washer and wait at least two minutes before plugging it back in.
If your model has a manual control panel, turn the knob to any setting other than the final spin.
Plug the unit back in and restore power to your laundry room.
Is there a reset button on a GE washing machine?
How to reset GE washers with a timer control knob. Unplug the washer or shut off the washer circuit breaker or fuse. Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting. Restore the power.
Is there a way to force my washer machine to drain water?
If you have a drain pump filter only, place the shallow container up against the machine, directly under the filter, to catch the water. Turn the knob slowly until water starts coming out. Fill the container, turn the knob off, dump the water into a sink or basin, and repeat until the water has been drained completely.
How do you force a washer to drain water?
How to drain a washer filled with water
Try the spin cycle.
Turn off the power and water supply.
Remove and check the drain hose.
Check to see if it will drain with the help of gravity.
Check your machine’s inner workings.
Check the drain pipe.
Drain manually if needed.
Call a service professional.
How do you force a washing machine to reset?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do I manually reset my washing machine?
How do you reset a washer that won’t spin?
Can you reset a washing machine by unplugging it?
Reset your washing machine
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.
How do you fix a washing machine that won’t drain?
Why does my GE washer not drain?
Kinked or Clogged Drain Hose. A washer’s drain hose carries water out of the washing machine after it’s used. If the hose is kinked or clogged, water won’t be able to flow when the machine is draining. Locate the hose on the back of the machine and inspect it for kinks, gently straightening out the hose if necessary.
How do I know if my drain pump is clogged?
Remove the drain hose by unscrewing the clamps holding it to the pump outlet. Look for blockages inside the hose, says Family Handyman. If you don’t see any, the pump may be blocked or faulty. To check it, you have to disconnect the belt connecting it to the drive motor.
How do I know if my washing machine drain hose is clogged?
Water Doesn’t Appear or Drain Normally
If the machine turns on and you hear the sound of the water pump, but no actual water appears, then you most likely have a clogged drain hose. The hose can be removed from the back of the machine and be checked for any dirt or dust that may have created a blockage.
How do you test a washing machine drain pump?
How do I know if my washing machine filter is blocked?
Signs That Your Linter Filter Needs Cleaning
You notice a buildup of laundry detergent or laundry softener residues on clothes.
The clothes do not dry as fast as they usually would.
The clothes don’t dry at all.
You notice a lot of lint falling off when the screen is inside the appliance.
Can a blocked filter stop a washing machine spinning?
Check the drain pump filter
If your washing machine’s filter is blocked it can stop your appliance from spinning.