“SPIN” light is flashing or “bALAnCINg” (balancing) is in the display (2015 and newer models): This means the washer cannot spin properly. After the wash cycle was complete, the items in the load were no longer evenly distributed enough in the tub to allow the spin out of the water.
Why does my GE washer keep getting off balance?
Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing.
How do you rebalance a GE top load washer?
A machine that is not level will rock during the spin cycle and cause the machine to be off balance. Top-loading washers automatically adjust to level. If something has shifted, you can level a top-loading washer by tipping the washer forward, then placing it back on the floor.
How do you balance a GE Profile washer?
Why does my GE washing machine say bALAnCINg? – Related Questions
What causes a GE washer to shake violently?
Unbalanced loads can cause the washer to vibrate more. Pause the unit, open the door, and manually redistribute the load. To check the machine, run a rinse and spin cycle with no load. If the washer’s level of vibration is normal, the unbalance was caused by the wash load.
What happens if washing machine is not balanced?
If the washer is unbalanced, you will likely find that it does not wash or spin as well as it should. An unbalanced washer will also often trigger an error code that will disrupt the washing cycle and potentially render the washer unusable until rebalanced.
How do you reset an unbalanced load on a GE washer?
How to reset GE washers with a timer control knob
Unplug the washer or shut off the washer circuit breaker or fuse.
Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting.
Restore the power.
Where is the balance ring on a GE washer?
It is attached to the inner clothes basket and allows the basket to spin smoothly if an uneven load creates an out-of-balance situation.
How do you balance a washing machine by yourself?
Leveling a Washing Machine
By placing a level on top of the machine, you can adjust the feet of the washer, not the actual floor, to make the machine level. This means that even if the floor itself is not level, you can compensate by adjusting the machine feet to be just right.
How do you reset a GE Profile washer?
If your washer isn’t working, disconnect it from the power source for one minute.Afterward, plug it back in and quickly lift and lower the lid six times within 12 seconds. And this should reset the motor so you can properly start a cycle.
How do I calibrate my GE washing machine?
Is there a reset switch on a GE washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I manually reset my washing machine?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
Can you reset a washing machine by unplugging it?
Reset your washing machine
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.
How do you reset a washing machine sensor?
How do you put a washing machine in diagnostic mode?
How do I run diagnostics on my GE washer?
How do I put my GE front load washer in diagnostic mode?
What is the first step of troubleshooting the malfunctioning washing machine?
The first thing you should always check is if the machine is plugged in. It may sound silly but dozens of times this problem has been solved by simply checking the plug. If the power cord is plugged in, check to be sure the outlet has power and that your circuit breaker wasn’t tripped. Check the water supply.