What are standard washer and dryer sizes? Standard washer and dryer sizes are generally 27 inches wide, 39 inches tall and 32 to 34 inches deep for front load units. Whereas, top load washers and dryers are typically 27 inches wide, 42 to 44 inches tall and less deep with depths of 27 to 28 inches.
How high should dryer outlet be?
Tips for Installing a Dryer Outlet
A height of about 30 to 36 inches from the floor usually suffices to keeps the plug accessible while hiding it from view behind the dryer. Orient the outlet properly: Orient the outlet so the L-shaped (neutral) slot is at the bottom.
How tall should a washing machine standpipe be?
The standpipe for the clothes washer must be trapped. The standpipe height should be at least 18 inches (457 mm) and no more than 42 inches above the trap weir.
How do you install a washer outlet box?
What is the proper height for a washing machine? – Related Questions
Where should a washer outlet be placed?
Electrical hookups for washers and dryers should be placed within 6 feet of the unit. While a minimum height for outlets in a home may very, depending on local building codes, for convenience both outlets should be placed between 34 and 36 inches high.
What is code for outlets in laundry room?
Laundry Room
A minimum of one 20-amp circuit is required for receptacles powering laundry equipment, and it can serve a gas dryer or washing machine. An electric dryer requires a dedicated 30-amp, 240-volt circuit that is wired with four conductors. Every receptacle must have GFCI protection.
How much does it cost to install a washer outlet box?
Most washers require a 120V outlet, which is the standard outlet you’ll find in most homes, while most dryers call for a 240V outlet. Installing a new outlet for either of these types usually costs around $100 to $250, including labor costs.
Does a washer outlet need to be on its own circuit?
But before you make a final choice on appliances consult with your Licensed Electrical Contractor because you may need an electrical upgrade. That beautiful washing machine needs to be on a 120-volt 15 or 20-amp receptacle, on its own circuit. The outlet should be placed out of reach and directly behind the machine.
Does a washing machine outlet have to be GFCI?
The NEC doesn’t require GFCI protection for clothes washing machines specifically, but it does for “Laundry Areas.”
Does a washer box need a vent?
All plumbing fixtures—including washing machines—must be vented. Improperly vented drains can be sluggish and noisy, and can emit hazardous fumes. Properly vented drains allow the P-trap to do its job: prevent sewer gases from escaping into your home.
What is the code for washing machine drain pipe?
According to the Universal Plumbing Code, the standard drain size for a washing machine is 2 inches. The absolute minimum should be about 1 1/2 inches. However, keep in mind that wash load capacities can vary by up to 400% or more depending on the model.
Can a washer and toilet share the same drain?
Your drains are connected – One of the main reasons your toilet gurgles when your washer machine drains is because your washer machine is connected to the toilet drain. This isn’t uncommon. Your washing machine might have been placed in between your toilet and sewer stack.
How high does a washer drain vent need to be?
The AAV will need to be at least 4 inches above the washing machine drain connection to create proper air pressure control.
Does a washing machine drain need to be elevated?
Elevating A Washing Machine Drain Hose
To be safe, you should always raise the drain hose above the level of the washing machine. This will keep any siphoning to a minimum. You may also take other measures to make sure you receive the best drainage possible.
Can a washing machine drain be too high?
A washing machine drain can be too high to pump. Washer drain pumps have a specified power rating, so they can only pump out water at a certain flow rate for a particular drain height. If the drain is too high, the flow rate will be too low to push the water out of the washer, resulting in backflow.
How tall should laundry drain pipe be?
Laundry standpipes must be tall enough to extend past the washing machine’s overflow line—typically 30-36” in height, or 18”-30” above the trap. P-trap. P-traps prevent hazardous and potentially flammable sewer gases from entering your home.
What is the minimum height for a drain?
The correct rough-in height for sink drains to pass the inspection is between 18 and 20 inches. Standard sink drains usually start from 24 inches and stop at 28 inches, so the rough-in height should be slightly lower than this height range.
What is the minimum height for a standpipe for a washing machine drain?
The standpipe shall extend not less than 30 inches (732 mm) above the weir of the standpipe trap and shall extend above the flood level rim of the laundry tray. The outlet of the laundry tray shall not be greater than 30 inches (762 mm) horizontal distance from the side of the standpipe.