Standard washer and dryer sizes are generally 27 inches wide, 39 inches tall and 32 to 34 inches deep for front load units. Whereas, top load washers and dryers are typically 27 inches wide, 42 to 44 inches tall and less deep with depths of 27 to 28 inches.
How high should dryer outlet be?
Tips for Installing a Dryer Outlet
A height of about 30 to 36 inches from the floor usually suffices to keeps the plug accessible while hiding it from view behind the dryer. Orient the outlet properly: Orient the outlet so the L-shaped (neutral) slot is at the bottom.
Where does the washer outlet go?
How tall should a washing machine standpipe be?
The standpipe for the clothes washer must be trapped. The standpipe height should be at least 18 inches (457 mm) and no more than 42 inches above the trap weir.
What is the height of a washer and dryer box? – Related Questions
What is the code for washing machine drain pipe?
According to the Universal Plumbing Code, the standard drain size for a washing machine is 2 inches. The absolute minimum should be about 1 1/2 inches. However, keep in mind that wash load capacities can vary by up to 400% or more depending on the model.
What is code for washing machine standpipe?
The standpipe shall extend not less than 30 inches (762 mm) above the weir of the standpipe trap and shall extend above the flood level rim of the laundry tray. The outlet of the laundry tray shall not be greater than 30 inches (762 mm) horizontal distance from the side of the standpipe.
How high should the drain pipe be behind a washing machine?
Laundry standpipes must be tall enough to extend past the washing machine’s overflow line—typically 30-36” in height, or 18”-30” above the trap. P-trap. P-traps prevent hazardous and potentially flammable sewer gases from entering your home.
What is the minimum height of a standpipe?
Also, the 18-inch minimum height of the standpipe intends to prevent the possibility of the clothes washer’s pumped waste from overflowing the standpipe.
What is the maximum height of a standpipe?
Standpipes shall be 2 inches (51 mm) in diameter and not less than 18 inches (762 mm) or more than 48 inches (1219 mm) in height as measured from the crown weir. The standpipe shall extend 34 inches (864 mm) minimum above the base of the clothes washer unless recommended otherwise by the manufacturer.
How high can a washer drain pipe be?
Generally, the maximum height is around 39″ (99 cm). Newer washers often have a drain hose permanently attached, which is designed to make drain installation fool proof.
Can a washing machine drain be too high?
A washing machine drain can be too high to pump. Washer drain pumps have a specified power rating, so they can only pump out water at a certain flow rate for a particular drain height. If the drain is too high, the flow rate will be too low to push the water out of the washer, resulting in backflow.
How long can a washing machine outlet pipe be?
Washing machines come with standard 1.5 m (4.9 ft) hoses, but you can safely extend them with pipes that are a maximum of 1.2 m (4 ft) long.
Can you put a 90 in a drain line?
It’s a bad plumbing practice to have a hard 90-degree bend in a horizontal drain line that’s buried in a slab or otherwise hidden. If you have to make a 90-degree bend, use two 45-degree fittings and put a small piece of straight pipe between the fittings, if possible.
How far can a drain line run without a vent?
For pipes that have a diameter of 3 inches the distance is 6 feet and for a 4-inch pipe the most it should be away from the vent is 10 feet. Keep in mind that toilets have their own traps so there is no need to have one on the drain line, but it still must have a vent.
Can a drain line be too steep?
If the slope is not steep enough, the sewage slows down, resulting in clogs. If it’s too steep, water and solids can separate, causing solids to accumulate in the pipe.
Can you have too much slope in drain pipe?
The ideal slope of any drain line is ¼ inch per foot of pipe. In other words, for every foot the pipe travels horizontally, it should be dropping ¼ inch vertically. Many drains either have too little slope or too much slope. That’s right, it is possible to have too much slope in your drain lines.
Can a shower and toilet share the same drain?
In short, it is possible to connect the toilet drainage line and the shower drainage line, as long as they both have separate waste trap arms. However, do note that combining them may also lead to blockages, which can cause smells to come from certain drains.
How much slope does a PVC drain pipe need?
For 4-inch PVC piping and a building sewer less than 50 feet long, the minimum slope is 1 inch in 8 feet, or 1/8-inch per foot, and the maximum is 1/4-inch per foot. For sewers longer than 50 feet, the slope should be 1/4-inch per foot.
What is code for slope of drain pipe?
According to the California Plumbing Code, a residential sewer must begin two feet outside the building, connect to the public sewer and have a minimum slope of 1/4 inch per foot.
How many bends can you have in a drain pipe?
How many bends are allowed in a sewer line? As many as you need, but use as few as you can. Under IPC – 708.3. 3, “Cleanouts shall be installed at each change of direction greater than 45 degrees (0.79 rad) in the building sewer, building drain and horizontal waste or soil lines.