The nut of a banjo or any stringed instrument is that small piece of hard material which holds and anchors the strings at the end of the neck closest to the peghead. The nut holds the strings at the proper height above the fingerboard and determines the spacing of the strings across the neck.
How high should the nut be on a banjo?
The gap between the top of the 7th fret and the bottom of the string is usually somewhere between 5 thousandths of an inch up to 25 thousandths of an inch for most well set up banjos.
What are the parts of a banjo called?
The pot assembly part of the construction of the banjo has the following components:
Banjo rim. The wood rim is the main part of the pot.
Co-ordinator rods. These steel rods keep the rim stable.
Tone ring.
Banjo head.
Banjo bridge.
Tension hoop.
Hooks and nuts.
Flange.
How wide is a banjo nut?
Size is 1-1/4” x 5/16” x 1/8”.
What is a banjo nut? – Related Questions
What happens if a man’s banjo snaps?
In most cases, the tear will get better without treatment. Once it has healed, you can try using a lubricant during sex to prevent the problem from happening again. If it does not heal, go to a GP or local sexual health clinic.
How tight should a banjo skin be?
For those of you with experience and a great ear, factory recommendations are to tighten it between G and G# on our frosted top heads. For the rest of us this means that the banjo head should give just a little to gentle pressure from our hand and the bridge should definitely look like it is sitting on a flat surface.
What size is a banjo bolt?
Product Specifications
Bolt Thread Size:
M10 X 1.5
Packaging Type:
Bag
Thread Diameter:
10 mm
Thread Pitch:
1.5 mm
Threads Per Inch:
1
What is the width of a nut?
They typically go between 1 11/16” to 1 3/4”, but some go to 1 7/8” and 1 23/32”. Even though the differences between these nut widths are incredibly small, your hands can still feel it. It’s important to keep in mind that there’s no set pairing of nut width and string spacing.
What is standard nut width?
The most common nut width is best known thanks to the electric guitar and especially the world-famous Stratocaster from Fender. They have a nut width of 1 11/16 inches or 42.8 millimeters, usually referred to as 43 millimeters.
How wide should nut slots be?
The individual slot widths will be a function of the individual string gauges and will determine what gauged file you use on each nut slot. As a rule, you typically want to cut a nut slot slightly wider than the actual string so the slot does not bind or choke the strings at the nut.
How far should strings sit in a nut?
A good measurement is about 1/16″ in from each end of the first fret (measuring from the top of the beveled fret ends). Put the two outside E strings on the guitar and, looking straight down on the top of the nut, move these strings together or apart until their spacing is correct for you.
Can a nut slot be too wide?
A too-wide nut slot is not necessarily all that bad.
The strings may still bear at the front edge, be supported along the entire slot, be at the right height and spaced evenly. If your nut has deep grooves that are too wide, and the whole thing looks messy, don’t fret.
What happens if nut slot is too wide?
If the slots are too wide then the string will be able to move from side to side. If the slots are too narrow then the strings will stick in the slots making tuning more difficult. If the slots are too deep the open strings will rattle/buzz.
How do I know if my nut slot is too low?
To check nut-slot height, hold the string down at the third fret, and see how much it moves over the first fret. This is similar to checking neck relief, but the string should move much less. If the string doesn’t move at all, chances are the slot is too low.
How do you turn a nut into a tight space?
How do you smooth a nut slot?
Instead, take a small piece of 800 or 1,000 grit Wet And Dry abrasive paper, wrap it around the string and push it into the offending slot. The idea is to smooth the surfaces of the slot and not to deepen it. Work the paper back and forth a few times, then pop the string back in to test your progress.
Can you file a guitar nut with sandpaper?
How Should guitar strings sit in the nut?
Ideally, your wound strings should have about half to two-thirds of their diameter in their slots and the unwound strings should sit just below the surface.