The purpose of a control board is basically the same as a timer; energize washing machine components at the proper time. To do this the control board monitors sensors throughout the washing machine to regulate water temperature, wash and spin speeds, fill and drain time as well as user commands.
How do you reset the control board on a washing machine?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do you test a washing machine control board?
How to test a washing machine control board
- Locate the control board in your washer (usually behind the control panel in most washers)
- Use a multimeter and check for continuity between the terminals on the control board.
- If you see continuity, then the control board may not be the problem.
How much does it cost to replace a washer control board?
If it’s faulty, you may be unable to operate the washer’s settings properly. You have to budget $275 to $400 when planning to replace a Whirlpool washer’s control board.
What does washing machine control board do? – Related Questions
Is it worth fixing a washing machine?
If your washer needs a major repair such as a new motor, tub or transmission, you’re often better off replacing the washer rather than repairing it; a major repair often costs more than half the price of a replacement washer.
What can cause a control board to fail?
Environmental Factors: Exposure to heat, dust and moisture, accidental impact (drops and falls), and power overloads/surges can be causes of circuit board failure. However, the most damaging cause of premature circuit board failure is electrostatic discharge (ESD) at the assembly stage.
How do you know if a board is damaged?
Check for signs of damage on the circuit board, such as crushed components, bulges, cracked wires, misplaced or extra solder, burn marks and scratches that indicate that the board needs to either be replaced or to be repaired. It is possible for scratches to expose and damage the connections beneath the lamination.
Can you repair a control board?
Luckily, it’s possible to repair or remanufacture boards to make them like new again. This does one of two things. Either the board in question can be returned to its original device, making it function again. Or, it can be used in a completely different device, as a form of recycling if you will.
How can you tell if a circuit board is blown?
Start with a Visual Inspection
Often, circuit boards deployed in the field are damaged by electrical surges and there are telltale signs on the PCB. Look for a burnt spot, particularly on the power supply module or I/O and connectivity ports. Pay attention to cracked ICs, broken traces, and blown capacitors.
Can control boards be repaired?
Luckily, it’s possible to repair or remanufacture boards to make them like new again. This does one of two things. Either the board in question can be returned to its original device, making it function again. Or, it can be used in a completely different device, as a form of recycling if you will.
How much does it cost to replace a control board on a dishwasher?
While minor repairs such as replacing the water valve or blown fuse typically cost below $150, repairs like replacing the electronic control board or pump assembly can cost more than $400.
How do you diagnose washer control and program problems?
How to Diagnose Washing Machine Control and Program Problems
- What You Will Need:
- Switch Off Your Appliance.
- Check 1 – Turning The Machine On.
- Check 2 – Recognise That It Is Filled With Water.
- Check 3 – Heating The Water & Proceed With Wash Cycle.
- Check 4 – Drain The Water & Proceed With Rinse Cycle.
How do I replace the control board on my GE washer?
How to Replace Your GE Washer’s Control Board When It Errors Out or Stops Working
- Unplug the washing machine. This is the first step to any appliance repair project.
- Disassemble the washer. Pull the washer away from the wall.
- Remove the old control board.
- Install the new control board.
- Reassemble the washer.
How do you reset a control board?
Control panel reset.
- Click Search.
- Type restore.
- Open create a restore point.
- Click the system restore button.
- Hit Next.
- Pick a restore point (Preferably a date before the issue happened)
- Wait for the process to finish.
How do you fix a control board?
How To Repair Circuit Boards
- Gather the tools and other materials that you’ll need.
- Remove the damaged pad or component.
- Clean the track and remove solder.
- Place your copper tape over the track.
- Solder the joints.
- Restore the PCB through-hole.
- Place and solder your component.
- Trim excess tape from the repaired area.
What causes a GE washing machine not to agitate?
If the washer is not agitating, you may need to reset your washer motor. If your washer senses a power spike, an unbalanced load or disruption in power, it will send a fault code to the motor and may require the motor to be reset.
What is the most likely cause if a washing machine will not agitate or spin?
Here are some of the main reasons your washing machine agitator not spinning: An obstacle jammed in the agitator. A broken lid switch. A loose or broken drive belt.
What is wrong with my washer if it won’t agitate?
Your washer may not be agitating due to worn-out directional cogs. Check to see if your machine’s agitator has two parts, allowing it to move the water left or right. If it does, and the cogs are damaged, the upper part of the agitator won’t properly connect to the bottom part.