To determine the age of your appliance, use your serial number (not model number) to find date of manufacture. Kenmore serial numbers begin with two letters followed by six numbers. The 2 letters at the beginning of the serial number tell you the month and year it was made.
How do I clean the filter on my Kenmore Series 500 washer?
How many years does a Kenmore washer last?
A typical washer should last 10-13 years. Top-loading washers typically last a few years longer than their front-loading brethren. If you use a stacked washer/dryer combo, you may have to replace both if one starts acting up.
How do I reset my Kenmore Series 500 washer?
How old is my Kenmore 500 washer? – Related Questions
How do you run diagnostics on a Kenmore 500 washer?
Why is my Kenmore 500 series washer not spinning?
The lid switch is a safety device that prevents the washer from going into spin mode when the lid is open. If the lid switch doesn’t work, the washer won’t spin even when closed. Replace the lid switch with a manufacturer-approved replacement part.
Where is the reset button on my Kenmore washing machine?
How do you force a washing machine to reset?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do I reset the control panel on my washing machine?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I force restart my washing machine?
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
What causes a washing machine not to start?
You should check the outlet to make sure it’s working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated. Sometimes it’s as simple as opening and closing the door to reset the washer.
What causes a washing machine not to cycle?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
What causes a washing machine to not spin and drain?
Top reasons washers won’t spin or drain
The coupler can wear out over time or fail, especially if the tub is consistently overloaded. Similarly, a drive belt can wear out, break, or slip on the pulleys. In both cases, the tub won’t spin until the worn coupler or damaged belt is replaced.
What causes washing machine not to spin or rinse?
The most probable cause is a clogged pump filter. The pump filter should be cleaned every three months or when it’s clogged. This filter is installed to catch foreign items like buttons or coins and to prevent these items from entering the drain hose. It’s located at the bottom right-hand corner of your machine.
What is the most likely cause if a washing machine will not agitate or spin?
A major reason that your washing machine has stopped agitating may be that there’s a fault with the drive belt. The belt could be slipping because it’s loose or it may have snapped completely. If you’re going to fix an issue like this you’ll need to be fairly handy or call a repairperson for help.