The UE error code sometimes appears because the washer is too full for the control board to redistribute the load during the rebalance routine. In this case, remove some garments and restart the cycle in Rinse/Spin mode. In the future, loosely place items in the basket; don’t pack down the load and add more garments.
How do I fix the UE on my washing machine?
The uE/UE code indicates that the washer is attempting to balance the load, which may be the result of the unit not being leveled correctly or the load itself.
Run rinse and spin cycle without load.
Empty the drum completely.
Power the unit on.
Select the RINSE AND SPIN cycle.
Press start.
How do you fix UE?
The UE Error Code means you have an unbalanced load.
There are 3 easy fixes.
Check the washer legs. All four should rest evenly on the ground with nothing underneath them.
Redistribute the wash.
Try turning it off and on.
Why does my washing machine shows UE?
When an UE error message is displayed on Samsung Washing Machine, it is indicating that the laundry load is unbalanced and has stopped the spin for safety reasons. It is vital to ensure that the load is evenly balanced when using a spin cycle.
How do you fix a UE code on a Kenmore washer? – Related Questions
Can an unbalanced washer be fixed?
If you determine that the washer is unbalanced, the washer’s feet can be adjusted to balance the washer. Depending on the type of washer, it may have feet at the back that self-adjust when the front feet are adjusted.
Can an unbalanced washing machine cause damage?
An unbalanced washing machine can experience serious damage during the spin cycle. This is because the drum or the tub of the machine will bang against the inside of the washer. You will end up having to spend a lot more on repairing your machine or replacing it.
How do you fix an unbalanced LG washer?
Using a level tool is the best way to check and fix the issue. If the level tool shows you the washer is not level, the washer’s legs should be adjusted until the washer is level. To adjust the leveling legs, locate the locking nut on the leg and loosen it with a wrench. Adjust the legs until the washer is level.
How do I rebalance my LG washing machine?
How do I balance my Samsung washer?
1 Turn the washing machine off and then on again.
2 Press and hold Prefer Mode or Smart Control for 3 seconds.
Use the Up/Down arrows to select Calibration.
Press OK.
5 Press the Start/Pause button to begin Calibration Mode.
How do I clear the error code on my LG washing machine?
How to reset the washing machine:
Press POWER to turn the washer off.
Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
With the power disabled, press and hold the START/PAUSE button for 5 seconds.
Plug the washer back in, or turn the circuit breaker back on.
How do you force a washing machine to reset?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do you reset a washing machine sensor?
Is there a reset button on a washing machine?
Reset your washing machine
There really isn’t a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.
How do you reset a washing machine without unplugging it?
Washers Without a Reset Button
For washers with a knob control, turn the dial clockwise to any cycle other than “Final Spin.” With button controls, select any cycle other than “Spin.” Check that the water to the washing machine is on. Turn the breaker back on. Turn the washing machine on.
How do I reset my top loader washing machine?
Motor Reset Procedure:
Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.
How do you put a washing machine in diagnostic mode?
How do I run a diagnostic on my Kenmore washer?
How do you run a diagnostic cycle on a Kenmore washer?
How do I reset my washing machine motherboard?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I reset the control panel on my Kenmore washer?