This guide covers all major GE washer models, including:
Step 1 – Inspect the lid switch.
Step 2 – Inspect the drive belt.
Step 3 – Inspect the motor coupling.
Step 4 – Inspect the door latch.
Step 5 – Inspect the motor control board.
Step 6 – Inspect the clutch.
Step 7 – Inspect the rotor.
How do I force my GE washer to spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
Why is my GE washer not draining or spinning?
This usually indicates the washer took too long to pump the water out. There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If the washer drains properly, then the clog has likely cleared.
Why does my washer turn on but not spin?
If your washing machine is not spinning but is making noise, a broken drive belt, or a drive belt that has slipped off the pulley wheel, might be the culprit. To determine if this is the case, remove the back of the washer and visually check to see if the belt is still on the pulley.
How do you fix a GE washer that won’t spin? – Related Questions
How do you reset the spin cycle on a GE washer?
How to Reset GE Washer Models
Shut off the circuit breaks or the fuse to the washer.
Unplug your washer and wait at least two minutes before plugging it back in.
If your model has a manual control panel, turn the knob to any setting other than the final spin.
Plug the unit back in and restore power to your laundry room.
How do I reset my GE Profile washer?
Unplug the washer or shut off the washer circuit breaker or fuse. Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting. Restore the power.
Does my GE washer have a reset button?
If your washer isn’t working, disconnect it from the power source for one minute. Afterward, plug it back in and quickly lift and lower the lid six times within 12 seconds. And this should reset the motor so you can properly start a cycle.
How do I put my GE washer in diagnostic mode?
How do I reset my spin?
Why is the spin light flashing on my GE washer?
Spin LED light is flashing: If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle and will stay illuminated for a short time after cycle completion.
How do I fix the spin cycle on my washing machine?
If the drum stops spinning mid-cycle, try stopping the machine, draining the water and rearranging the laundry. You might be using too much detergent or an inappropriate type for your appliance. In this case, your washing machine will stop the spinning cycle and try to absorb the excess foam in its drum.
What do you do if your spin cycle isn’t working?
A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure. To troubleshoot this, hold the switch down with your finger (with the lid open) and start a spin cycle.
How do you force a spin cycle?
Is it worth fixing a washer?
Repair: If the repair would cost less than 50% of the price of a new appliance and your machine still has several expected years of life left, a quick fix could be a cost-effective solution over replacing the entire washer. An active warranty can also make any repair worthwhile.
How long will a GE washer last?
Washing machines, on average, last around 10 years, according to Consumer Reports.
How much does it cost to fix a washing machine that doesn’t spin?
Washing machine repair costs by problem
Problem
Cost range
Leaking
$75 – $200
Won’t drain
$85 – $225
Won’t spin
$120 – $350
Unbalanced drum
$200 – $400
Is it worth repairing a 7 year old washing machine?
Consumer Reports recommends replacing any appliance that’s more than eight years old, unless it’s a high-end model and has a particular appeal to you. Others suggest replacing any top-loading washer manufactured in 1999 or earlier.