How do I fix my OE washing machine?

OE can be triggered by a kinked drain hose or a clogged drain pump filter.

Check for kinked drain hose. Check behind the washer to ensure that the drain hose is not kinked or clogged.
Test the drain pump.
Do you hear the humming sound?
Clean drain pump filter.
Run tub clean cycle.
Request Repair.

How do you clean a Kenmore washer drain?

How do you fix a Kenmore washer that won’t drain?

If your washing machine does not automatically drain the wastewater, the machine’s waste hose might be clogged. To unclog the waste hose, remove the hose from the back of the washing machine by unclipping it. Then, clear it out using running water and a toilet snake.

How do I fix the error code on my Kenmore washer?

Too much detergent

If you see lots of suds in the tub, let the washer sit idle for 30 minutes so the foam dissipates. Next, start a Drain/Spin cycle to remove the sudsy water. Then run a new cycle without adding any detergent to wash and rinse the current load.

How do I fix my OE washing machine? – Related Questions

How do I reset my Kenmore washer?

Is there a recall on Kenmore washers?

The units come in beige, white and graphite steel colors. Recalled washing machines have the following model and serial number ranges: LG models WT5001CW, WT5101HV and WT5101HW with serial numbers 002KW though 111KW. Kenmore Elite models: 29002, 29272 and 29278 with serial numbers 005KW through 111KW.

How do you reset a washing machine sensor?

There really isn’t a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.

How do I put my Kenmore washer in diagnostic mode?

3 Answers

With the washer empty, close the door.
Push “control/on” or “Start”
Select “Drain/Spin”
Select “No Spin” by pressing SPIN SPEED touchpad.
Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
C:00 should light up and begin the diagnostic.

Why does my washing machine keep saying error?

Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.

How do you reset a washing machine code?

Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.

How do I reset my top loader washing machine?

Motor Reset Procedure:

Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.

How do you open a washing machine door with error code?

How do you open a washing machine door after error code?

Turning off the machine at the mains should allow the door lock to cool down, and after a few minutes, you’ll be able to open the washing machine door. The interlocks can take some time to release at the end of the cycle, so be patient. The most common cause is water left in the machine. Try running a spin/drain cycle.

How do you manually unlock a front load washer?

Can you bypass the door lock on a front load washer?

You can bypass your washing machine door by disconnecting the door from the appliance. Look for the screws that hold the door unfasten the crews and lift the top panel of the door.