Of course it does. These are to be removed by the installer or whomever does the installation. The bolts are worth saving somewhere if you ever move, or if you sell the washer to someone else for them to move.
Do all washing machines have shipping bolts?
Front loading washing machines have approximately 4 shipping bolts that are very specific to the appliance’s make and model. All manufacturers ship front loaders with the shipping bolts inserted to avoid internal suspension and structural damage to the washer during transport.
Does Samsung top load washer have shipping bolts?
What happens if you don’t remove shipping bolts from washer?
You need to remove the shipping bolts. If the four shipping bolts of your machine are still attached to the back of the washer, they will cause a loud noise and vibration during the operation of the machine; which can lead to a permanent damage of the washer.
Do top load washers have shipping bolts? – Related Questions
Do all new washing machines have transit bolts?
All new washing machines are fitted with a transit bolts to protect the machine against damage in transit. Transit locks and bolts must be removed before you use your appliance.
Can you move a washing machine without transit bolts?
Moving a washing machine without transit bolts will run the serious risk of damaging your machine, so we strongly advise against it. Washing machine transit bolts are a vital piece of equipment required to move your washing machine securely.
Do you remove shipping bolts?
It is necessary to remove all shipping material and shipping bolts for proper operation and to avoid excessive noise from the washer. Follow the below steps to remove the shipping bolts: IMPORTANT: Do not plug the washer in until installation has been completed.
Do washers help bolts stay tight?
Washers are typically wider than the bolt head, with the additional surface area adding extra friction to the joint to maintain the clamp force. However, simple split washers, sometimes called helical spring washers, have been found to actually loosen the bolt under vibration even faster than a joint with no washer.
Will movers disconnect washing machine?
Most moving companies, like Master Movers, do not disconnect or reconnect any power or water lines to your appliances. Preparing appliances for moving, such as your washer, dryer and refrigerator, falls on homeowners, who can do it themselves or hire a professional.
Do washers prevent nuts from loosening?
In theory, the washer is squashed flat when the nut is tightened against mounting surface so that its sharp edges dig in to prevent the threaded fastener unwinding. In practise, it might delay the length of time it takes for the bolt to loosen, but it will not permanently prevent it.
How do you fix a bolt that keeps coming loose?
What goes first lock nut or washer?
When used correctly, a lock washer will hold the nut or other threaded fastener in place. To help it accomplish this, put the lock washer on first, below the fastener. If your project calls for other washers or hardware elements, they should go on before the lock washer so that it can hold them in place.
Should washer go under nut or bolt?
The lock washer should be placed under your threaded fastener – i.e., underneath a nut or the head of a screw or bolt. In assemblies where you have a nut and a bolt, the washer should be placed between the nut and the head of the bolt. You can then tighten the threaded fastener as normal.
Is it OK to stack washers on a bolt?
It is not a good practice to stack washers in a fastener joint. Each stacked element acts like springs in series, consequently, fastener joint stiffness would be compromised.
Where do you put washers on bolts?
Spring washers are also known as locking washers. These washers are made by removing part of a flat washer so that a twisted shape forms. However, spring washers are placed on the nut side of the fastener only, unlike flat washers, which are placed on the bolt and nut sides.
Why is a washer installed under a nut?
Washers have traditionally been used to protect the joint surface from damage during the tightening process and to distribute the load under the bolt head and nut. The stress under the face of a standard hexagon headed nut can result in indentation into standard strength steel surfaces.
Do you need a washer under a nut?
Washers are important. They ensure that a nut is installed properly and prevent softer materials from damage by distributing the pressure over a greater surface area. Are washers necessary? Washers are not always necessary but it is common practice to use them anyway.