They was vary easy to use and made the Job so easy. The hidden fasteners worked great. The hidden fasteners worked great. It made grooved deck board installation easy and fast, and no nails could be seen on boards.
How tight should Trex hidden fasteners be?
Do Trex hidden fasteners go on every joist?
NOTE: When using hidden fasteners (both start and connector clips), one must be used on every joist. ° # of joists x # of decking boards = # of connector clips needed.
What is the best hidden fasteners for composite decking?
Whether you’re using solid wood, composite, or PVC decking, one of the top products listed below may be a fitting choice.
BEST OVERALL: National Nail Camo 1750-Pro Pack 2 3/8 inch.
RUNNER UP: Starborn Industries Pro Plug System Wood Deck Kit.
BEST FOR COMPOSITES: TREX Hideaway Plastic Fasteners with Screws.
Are Trex hidden fasteners any good? – Related Questions
Are hidden deck fasteners worth it?
Hidden deck fasteners are a nice way to keep the surface of your deck looking clear and unencumbered. But they are not the right fastener for all decks. In fact, using hidden deck fasteners inappropriately is a formula for failure. Some deck projects require the stronger fastening power of face screws.
Does composite decking need gap between boards?
To make sure that there’s enough room between the boards to allow for the small amount of expansion and contraction that can occur on particularly hot or cold days, you should: Allow a 3-5mm gap on either side of the deck boards. Allow at least 5mm between deck boards and adjoining structures or posts.
What type of fasteners use on composite decking?
Only Cortex® and TOPLoc® fasteners work for the entire deck surface.
How do you hide screws on a composite deck?
What fasteners work with Trex?
The Start Clip. These are black, stainless steel fasteners designed exclusively for Trex and used to install the perimeter deck boards.
What fasteners to use with Trex?
Trex recommends the use of two screws per joist.
Use recommended stainless steel screws in any areas near bodies of saltwater. 2-3/4″ or 3″ screws can be used with Trex 2×6 product. Muro T-Screw M-TX0300SEP listed above is approved for 2×6 decking (can also be used with standard 1″ (decking as listed above).
What should not be put on a Trex deck?
Avoid using products containing bleach or acid, as they will lighten the surface of your deck. Never use acetone or any other solvents on Trex railings; it will make them dull or cause damage. Stay away from using a power washer on any of the older generation Trex products.
Is it OK to screw down Trex decking?
Strictly speaking, yes you can, but you shouldn’t. As well as voiding your composite decking warranty, screwing boards in place will cause you all kinds of problems in the long run, which you will need to return to and rectify, so it’s best to get it right first time.
Should you pre drill Trex?
In the past, no matter what type of deck board you were installing, the answer to this question would indefinitely be yes. However, with advancements in fastener technology, pre-drilling in most composite and capstock deck boards is no longer necessary. Composite deck screws have been consistently used by the industry.
What voids the Trex warranty?
If the surface of the Product is damaged or punctured, this warranty will be voided. Paint or Other Materials Applied to the Product: If paint or other coating materials are applied to the Product, this warranty will be voided.
Do you need to leave gap for Trex decking?
You must gap Trex® decking, both end-to-end and width-to-width. Gapping is necessary for drainage and the slight thermal expansion and contraction of Trex decking boards. Gapping also allows for the shrinkage of the wood joist system.
Do the cut ends of Trex decking need to be sealed?
You won’t ever need to seal or stain the deck, and you certainly don’t have to (and shouldn’t) paint it. And since Trex is a composite material, you don’t have to carry out long-term maintenance such as replacing rotted deck boards.
Why are there grooves on the bottom of Trex decking?
The most unique feature of Trex Enhance boards are their scalloped bottoms. The undersides of Enhance boards are lined with grooves that help make Trex Enhance lighter and easier to transport before and during your deck build.
Why does Trex have grooves on the bottom?
Having grooves on the bottom of your decking planks allows for greater airflow from the timber frame beneath and the underside of the board. This is especially important as it prevents the build-up of damp conditions which can lead to wood rot.