Shut off the circuit breaks or the fuse to the washer.
Unplug your washer and wait at least two minutes before plugging it back in.
If your model has a manual control panel, turn the knob to any setting other than the final spin.
Plug the unit back in and restore power to your laundry room.
Why is my GE washing machine not turning on?
Here’s how to assess for power issues when your GE washer won’t start: Check the power cord: Make sure it’s completely plugged into a functioning outlet and free of damage. Avoid extension cords: They can’t reliably transmit the voltage a washer requires, resulting in surges that interrupt power.
Why does my GE front load washer keep turning off?
If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
Where is the error code on a GE front load washer?
To enter the error code test mode on a GE front load washer, rotate the control knob until t02 is displayed in the control panel then press start/pause to enter the test mode. This is where all error codes are stored.
How do I reset my GE front load washer? – Related Questions
How do I reset the error code on my GE washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I reset my GE washer control board?
How to reset GE washers with a timer control knob
Unplug the washer or shut off the washer circuit breaker or fuse.
Turn the timer knob around in a clockwise direction once, bringing it back to any position other than the final spin setting.
Restore the power.
What are the codes on a GE washing machine?
GE front-load washer error codes
E22. No fill or slow fill. Check/ Repair.
E23. Washer overfilled with water. Check/
E30. No drain. Check/
E31. Draining timed out. Check/
E38. Dispenser error. Check/
E39. Dispenser won’t move. Check/
E42 or E45. Drive motor drawing too much current. Check/
E43. Inverter control board defective. Check/
How do you read a washer error code?
What does E01 and F09 mean on a washing machine?
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
How do I put my GE washer in test mode?
How do I manually reset my washing machine?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
Why won’t my GE washer wash or spin?
The most common reason GE washers stop spinning is a faulty lid switch. The purpose of the switch is to monitor if your washer door is closed, so the main control board knows to let the washer cycle start.
How do you reset a GE washer that won’t spin?
How do I force my GE washer to spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
How do I get my washing machine to spin again?
If the drum stops spinning mid-cycle, try stopping the machine, draining the water and rearranging the laundry. You might be using too much detergent or an inappropriate type for your appliance. In this case, your washing machine will stop the spinning cycle and try to absorb the excess foam in its drum.
How do you force a spin cycle on a GE washer?
What causes a front loader not to spin?
Front-load washer tubs spin thanks to a drive belt that runs off of the motor. A loose, frayed, or torn belt could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.
Why is my washer not spinning but it will drain?
The washing machine drains but won’t spin. A displaced or faulty spin switch is the most likely cause. This small switch should be pressed down by the lid when it’s closed. If it isn’t pressed down, your machine may prevent the spin cycle as a safety measure.