If the water level seems too low, or if the washer does not fill completely, auto-sensing helps stabilize the amount of water used. The washer senses the size of the load and adds the correct amount of water for the load size. You may notice during a cycle that the wash load is not completely submerged in water.
How does sensing fill work?
How long is sensing fill?
These sensing spins may take 2 to 3 minutes before water is added to the load. The washer will then move the load briefly, pause to allow water to soak into the load, and resume adding water. This process may repeat until the correct amount of water has been added to the load.
Why is the sensing fill light flashing?
See the following troubleshooting link: http://products.geappliances.com/appliance/gea-support-search-content?contentId=16539 If the fill light flashes, check your house water supply. As soon as the light starts to flash, the washer will initiate a 4 minute lock-out period.
What does sensing fill mean on a washer? – Related Questions
How do you reset a washing machine sensor?
How do I reset the sensor on my Whirlpool washing machine?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP.Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
Why is my motion sensor light blinking red?
The flashing red light on a motion detector indicates that the device is in its walk test mode. In this mode, a user can walk around the area and check to make sure that motion is being detected.
What does sensing mean on LG washer?
After aligning the gears of the motor, the tub rotates for about 30 seconds in one direction to detect the weight of the laundry. Once load sensing is complete, the fill level, selected cycle, number of rinses, and spin speed are calculated and a total estimated time is displayed as water is supplied.
Why is the lid lock light flashing on Whirlpool washer?
The Lid Lock Light will flash if Lid Lock has not moved into the Lock Position, the Lock Motor can not be powered, or the Lid is not closed completely due to interference. Some models will lock immediately, while others will not lock until after the wash cycle has started.
Why is my Maytag washing machine blinking?
The Wash Light is On or Flashing when the water level does not change for a period of time OR water is present but the control does not detect the water level changing.
What does sensing mean on Maytag washer?
When the Start/Stop button is pressed, and the Water Level knob is set to Auto Sensing, the washer will fill and begin sensing to determine load size and balance. Once sensing is complete, the washer will fill to the appropriate level for the detected load size and then begin the wash phase of the cycle.
How do you reset the sensor on a Maytag washer?
Follow the below steps:
Remove the washer’s plug for one minute.
Reconnect the power, then lift and close the lid six times in a 12-second interval.
Keep in mind that for the procedure to function, the lid must close properly six times in a row.
Run a test load afterward to confirm that the washer has reset.
Is there a way to reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
What buttons do I push to reset my Maytag dishwasher?
How to reset a dishwasher control panel
First press the “Cancel/Resume” button, which won’t be illuminated, then unplug the appliance from the outlet.
Wait approximately 1 minute, plug the cord back into the AC outlet or flip the breaker back on.
Start a new cycle and check if the dishwasher is working properly.
How do I manually reset my washing machine?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do you bypass the sensor on a Maytag washer?
Here is a simple way to do this:
Let us say you have 2 lbs of clothes.
Add the 2 lbs of clothes in the washtub.
Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric.
Start the wash cycle.
You have successfully bypassed water level sensor.
What happens when you bypass a sensor?
Bypassing a sensor allows the alarm system to temporarily ignore a particular sensor. The system can arm stay or arm away and monitor all other sensors except those that are bypassed. This is used frequently when a sensor is malfunctioning or if a user wants to leave a window or door open during an arming cycle.
How do I trick my washer to add more water?
How do I get my Maytag washer to fill up with water?
If you would like to add the maximum amount of water to your wash cycle, turn the Water Level knob to the Deep Water Wash setting. NOTE: Expect longer cycle times due to extended fill times when using the Deep Water Wash option.