If you have a full size family or frequently have a guest or two over for a soak, a four to five person hot tub might be what you are looking for. Those looking for more personal space might also choose a tub that fits four to five adults.
How long should you stay in a hot spring?
The intense heat can cause dehydration, fainting, and even burns depending on the temperature, so stick to 10- or 15-minute soaks with breaks in between to allow your body temperature to return to normal.
Do hot springs help arthritis?
Immersion in warm water produces hydrostatic pressure on the body that results in reduced joint inflammation and increased mobility. The Arthritis Foundation notes, “soothing warmth and buoyancy of warm water makes it a safe, ideal environment for relieving arthritis pain and stiffness.”
Why is the power light blinking on my hot tub?
It also provides a diagnostic function–a blinking power indicator indicates that the heater high limit has tripped, meaning that either the spa water is above its acceptable temperature range, or a malfunction has occurred within the spa (such as low circulation due to clogged filters).
Should I get a 4 or 6 person hot tub? – Related Questions
How do I reset the power on my hot tub?
How do I reset my hot springs hot tub?
Is there a reset button on a hot tub?
Most hot tubs are fitted with a reset button in the event of overheating or a power surge. The button is typically located on the side of the control box behind the hot tub’s removable panel on the front side. Similar to disposal reset buttons, simply press the small red button in to reset it.
What are the codes on a hot tub?
Balboa
pd = Power supply, unit running on battery backup.
OH = Sensors reading 112-118° F.
OHH = Overheat. Spa has shut down.
OHS = Overheat.
Flo = Improper flow or pressure switch malfunction.
Cool = Water temp 20° below set point.
ICE = Potential freeze condition has been detected.
Sn1 = Hi-limit sensor malfunction.
How do I know if my hot tub fuse is blown?
Disconnect the power from the entire hot tube circuit. Then, test the fuse’s continuity with a Volt Ohm meter. If the Volt Ohm meter shows infinity, the fuse is blown.
Why did my hot tub suddenly stop working?
There are two main reasons your hot tub isn’t heating up properly; faults with the heater element, or problems with the water flow. The heater can fail for a few reasons but one of the most common is if it has been subject to corrosion caused by low PH in the water supply.
Why did my hot tub just stop working?
If your hot tub won’t heat the water properly, it could be the heater element or low flow from your pump. Most heating failure result from corrosion caused by low PH in water supply. Any PH below 7.0 damages the heating element and trips the GFCI breaker.
Why is my hot tub not powering on?
Check the main circuit breaker which provides power to the Hot Tub, reset the breaker, if it trips repeatedly it could be a faulty breaker or the voltage is incorrect, on some occasions you can have a faulty/over sensitive RCD, water in the isolator or a loose cable.
How do I get my hot tub to turn on?
Where is the fuse on my hot tub?
Is there a fuse in my hot tub?
Check the Internal Fuses
Some hot tubs and most swim spas have an internal fuse system. These fuses are designed to blow when there are voltage spikes.
How much does it cost to replace a hot tub circuit board?
Cost to Replace Spa Circuit Board: Hot tub PCBs range from $200-$600, with an average cost of $300.
What causes a hot tub to throw a breaker?
Moisture in your Hot Tub Breaker Box
Rainwater, splashout, or flooding can introduce enough dampness to flip a hot tub GFCI. The solution may be as easy as drying the inside of the breaker box with your towel, turning a fan or dehumidifier on near your outlet, and resetting the breaker once dry.
What destroys a hot tub?
Excess Contaminants
Don’t use your hot tub or swim spa as a bathtub, don’t dip right in after exercising or working in the garage. Hot tubs aren’t for bathing. The excess contaminants will ruin the water conditions and overwhelm the filters. Trust us, you don’t want to be in there with compromised water and filters.
What is common problems with hot tubs?
5 Most Common Hot Tub Problems and Repairs
Won’t Heat. If your hot tub won’t heat, then it’s simply a tub of cold water.
Jets Aren’t Working. The jets in your hot tub can deliver an invigorating water massage.
Noisy Pump.
Error Code on Control Panel.
Dirty Water.
Should a hot tub be on its own breaker?
Most full-size hot tubs are designed for 240 Volt electrical service. These hot tub wiring systems require a 40 to 60 Amp breaker and must be specially hardwired by a licensed electrician.