The retainer nut on most of our riding mower blades are a 5/8″ thread diameter. This sized thread diameter nut normally requires a 15/16″ wrench or socket tool in order to remove/install.
How do you get a stripped bolt out of a lawnmower?
How do you loosen a lawnmower bolt?
Put a wrench socket of the correct size on the head of the bolt securing the blade to the blade holder, and apply force to the wrench handle in the counterclockwise direction to loosen the blade bolt. The bolt may have a 1/2-inch, 5/8-inch or 3/4-inch head, depending on mower model, says DIY HomeOwner Hero.
Are bolts on mower blades left handed?
Yes.The bolts that hold the mower blades on a Craftsman mower in place are reverse threaded. That means that to tighten the bolt you must turn it to the left (counterclockwise), and to loosen it you must turn it to the right (clockwise).
What size is the lawn mower blade bolt? – Related Questions
How do you tell if a bolt is right or left?
Screw handedness refers to the direction that a screw’s thread wraps around its shaft. Right-handed threads run clockwise, and left-handed threads run counterclockwise.
Is a lawn mower blade bolt reverse threaded?
Most times, the blades of a lawn mower are reverse-threaded. However, you may be required to block the blade from turning in order to break the bolt loose. Removing your blade for sharpening or replacement will require the use of a socket wrench to unbolt the lock nut, which is often reverse-threaded.
Are lawn mower blade bolts left or right hand thread?
The mower’s bolts rotate in the standard direction with right-handed threading. If you want to fasten it securely, it must be tightened from 70 to 90-foot pounds.
Are lawn mower blades left-handed?
A single blade mower is usually right-handed. On a multiple bladed mower adjacent blades spin in opposite directions and one will be right-handed and the other left-handed.
How do you know if a bolt is reverse threaded?
Most bolts have a right-handed thread and turn in a clockwise direction as you screw them in. If you look at the threads of such a bolt, they appear to angle upward to the right (this is called pitch). Reverse-thread bolts have a left-handed thread and turn in a counter-clockwise direction when tightened.
Is there a left and right lawn mower blade?
Right-hand cut vs left-hand cut blades
Believe it or not, the cutting edge is not on the same side for all lawn mower blades. Right-hand cut lawn mower blades are overwhelmingly the most common type. Left-hand cut blades can be found on some mower’s manufactured by Kubota, Woods, Walker, and others.
What happens if you put mower blades on backwards?
Mower blades feature a cutting edge at both ends so, it is very common for people to install them upside down. If you install them upside down, you can do some major damage to your grass and maybe even your mower. You’ll be “cutting” with the dull side of the blade which will rip the grass vs. cut it.
Is it OK to tip a lawn mower on its side?
Although it is not the recommended way of tilting your riding lawn mower, you can tilt it on its side. Just make sure that you are tilting it on the correct side to prevent damage to your lawn mower.
How do you tell if mower blades are upside down?
Why should you not pull a mower backwards?
Simply, put, your mower will not perform as well when mowing in reverse. There are a number of reasons for this. One of the most immediately noticeable problems is that the grass will not get discharged underneath the deck. The cut is irregular, since mowing backwards means that the blades are running in reverse.
Should mower blades face up or down?
So when installing your blade, you want to make sure these “wings” are pointing upwards towards the underside of your deck, and the sharp side of the blade is the side that is closest to the grass.
Are mower blades supposed to line up?
Aligning the Blades
Some mower manuals, like this one from John Deere, make a point of saying that mower blades need to be aligned perpendicular to one another. To see if the mower blades are out of alignment, you first have to take off the cutting deck.
Why does my mower leave a row of grass between two blades?
Dull or Damaged Blades
Rows or streaks of uncut grass in your lawn may be the result of your lawnmower’s cutting blades being dull or otherwise damaged. Dull blades are the result of normal wear and tear from mowing. The blades can be sharpened with a bench grinder by you or a professional.
Should mower blades be sharp to the touch?
Mower blades should be aggressively sharp, but not as sharp as a razor’s edge. You should be able to touch the blade with your hand without getting cut. Contrary to popular belief, a lawn mower blade with a razor sharp edge will not cut grass better.
Do new mower blades need balancing?
While you should not sharpen new lawn mower blades, you should check to make sure they are balanced. Even though all of the new lawn mower blades I’ve bought have been balanced, it is worth checking. Nothing is worse than going through the process of installing a new blade and noticing vibration problems afterward.
Should mower deck wheels touch the ground when mowing?
Mower deck gauge wheels should be properly adjusted to prevent scalping grass on uneven terrain. The bottom of the wheels should sit approximately 1/8-1/2 of an inch from the ground, depending on your cutting height.